Siemens SIMATIC RF120C Скачать руководство пользователя страница 88

Страница: 88 / 92

AdvancedCmd and Ident profile

C.2 The "Ident profile" block

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

Table C- 2 Permitted settings for the "CMD" parameter

Parameter

Command

CMD_ID

LEN_DATA

ADR_TAG

ATTR

Write

71h

Length of the data

to be written

Address on the

transponder

Read

70h

Length of the data

to be read

Address on the

transponder

MEM-Status

73h

RF200: 83h

RF300: 82h, 83h

RF600: 84h, 85h

MOBY D: 83h

DEV-Status

74h

RF200: 81h

RF300: 81h, 86h

RF600: 87h, 88h, A0h,

A1h

MOBY U: 81h, 84h

MOBY D: 81h

Inventory

69h

RF600: 82h, 83h, 85h,

90h, 91h, 92h, A0h, A1h

Format

66h

Value: 15

The memory size

and the

initialization value

must be stored in

the data buffer

Details: See Function manual for RF620R/RF630R. There, the DEV status corresponds to the

"SLG-Status" command and Inventory corresponds to the "GET" command.

The attributes must be compiled as follows: 81h → 01h, 82h → 02h, 83h → 03h, 85h → 05h, 87h →

07h

, 90h → 10h, 91h → 11h, 92h → 12h, A0h → 20, A01 → 21

Details: refer to the Function manual for the RFID standard profile

As an alternative, the settings possible with the "AdvancedCmd" function block can also be

made with the Ident profile (see section "The "Ident profile" block (Page 88)").

C.2

The "Ident profile" block

Note
Parallel operation using the FB and Ident profile is not possible
The RF120C communications module must not be operated using the function blocks and

the Ident profile at the same time.

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды