Siemens SIMATIC NET SCALANCE W740 Series Скачать руководство пользователя

Страница: 63 / 456

Technical basics

4.9 iPRP

SCALANCE W780/W740 to IEEE 802.11n Web Based Management
Configuration Manual, 08/2018, C79000-G8976-C267-13

4.9

iPRP

The "Parallel Redundancy Protocol" (PRP) is a redundancy protocol for cabled networks. It

is defined in Part 3 of the IEC 62439 standard.
With the "industrial Parallel Redundancy Protocol" (iPRP) the PRP technology can be used

in wireless networks. This improves the availability of wireless communication.

How it works

A PRP network consists of two completely independent networks. If one network is

disrupted, the frames are sent without interruption/reconfiguration via the parallel redundant

network. To achieve this the Ethernet frames are sent to the recipient in duplicate via both

networks. Devices capable of PRP have at least two separate Ethernet interfaces that are

connected to independent networks.
With devices not capable of PRP a redundancy box (RedBox) is connected upstream. This

allows access for so-called Single Attached Nodes (SAN) to PRP networks. The RedBox

duplicates every Ethernet frame to be sent and adds a PRP trailer to the frame that among

other things contains a sequence number. The RedBox simultaneously sends a copy of the

frame to the PRP A and PRP B network. At the receiving end the duplicate frame is

discarded by the RedBox. For this the RedBox requires certain transfer times designed for

Ethernet networks. For this reason using PRP in WLAN networks results in duplicate and

delayed frames.
With iPRP this problem is solved and the use of PRP in WLAN with SCALANCE W700

devices becomes possible

Содержание SIMATIC NET SCALANCE W740 Series









































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET SCALANCE W740 Series

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W740 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE W740 Series, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET SCALANCE W740 Series

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W740 Series

Бренды по названию

Популярные бренды