manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Руководство пользователя

Поделиться
Скачать
Siemens SIMATIC Distributed I/O System DP/ASi Link Скачать руководство пользователя страница 91

8-5

Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b

In addition to the different displays described in Table 8-2 and Table 8-3,
combinations of several LEDs are also possible. Table 8-4 shows you the
meanings of the displays.

Table 8-4

Combination of several LEDs  

LEDs

Meaning

Remedy

All on

DP/ASi link starting up.

–

All on except ASi
POWER FAIL

A fault has occurred in the PROFIBUS-DP
during start-up.

Check the PROFIBUS-DP, the DP master
and the bus connection.

ASi SLAVE FAIL
flashing

DP/ASi link has not detected an ASi slave.

DP/ASi link not starting.

Check the ASi cable and the cable termina-
tion.

BF flashing

Station number 126 or 127 is set on the DIP
switch block or switch 8 is in OFF position.

Set the correct station number on the DIP
switch block.

Set switch 8 on the DIP switch block to ON
and set a valid station number in the EE-
PROM.

CONFIG ERROR
and all ASi SLAVE
FAIL light

Normal mode: ASi slave 31 has failed

S7 start-up: data record 128 missing

Check your configuration. Possibly no ASi
slaves have been configured.

If several ASi slaves have failed, the failed ASi slave having the lowest ASi
address is indicated with the ”ASi-SLAVE FAIL” LEDs. You recognize the
failure of several ASi slaves by the ”AUTOPROG AV” LED not being on.

Check, therefore, the ASi cable for damage in all cases as well.

If the DP/ASi link detects that an ASi slave has failed or that there is no
longer a connection to it, it takes the following action:

The input data to the DP master are reset to 0 for the failed ASi slave.

A diagnostic message is generated (refer to section 8.2)

All data, including the reset data of the failed ASi slave, are still transmitted
to the DP master.

If you have remedied the reason for the failure, you can establish immedi-
ately whether the DP/ASi link is working properly again. If everything is in
order, the DP/ASi link enters normal operation. Only the ”RUN” LED is on.

Combinations

ASi slave failure

DP/ASi link reac-
tion

Check

Diagnostics and Error Handling

Содержание SIMATIC Distributed I/O System DP/ASi Link

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды