Siemens SIMATIC Distributed I/O System DP/ASi Link Скачать руководство пользователя страница 30

Страница: 30 / 152

3-4

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

3.3

Configuration with T Connector and with Power Supply Connector

In a configuration with a power supply connector and a T connector, the DP/
ASi link is connected by means of a T connector to the PROFIBUS-DP.

The power supply is gated by means of the power supply connector with the
PROFIBUS-DP in a single cable.

A slave station can be disconnected at any time from the bus without the ”bus
traffic” being interrupted for the other slave stations.

The power supply is fed along the bus cable, i.e. an external power supply of
the slave station is not required.

The degree of expansion with a PS connector is limited (refer to section 3.4).

You use cables of different design for the installation:

If you wish to use prefabricated Siemens cables, please turn to sec-
tion 4.4.4.

If you wish to prepare your own cables, please turn to section 4.4.7.

Fig. 3-3 shows a possible installation for the configuration with a power sup-
ply connector and with a T connector:

External
power supply

PROFIBUS-DP

cntr

DP/ASi link

Figure 3-3

PROFIBUS-DP and power supply looped through by means of T
connector

Definition

Advantage

Constraint

Cables

Installation

Configuration Options

Содержание SIMATIC Distributed I/O System DP/ASi Link

























































































































































Результаты поиска

Содержание SIMATIC Distributed I/O System DP/ASi Link

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC Distributed I/O System DP/ASi Link, Руководство пользователя

Результаты поиска

Содержание SIMATIC Distributed I/O System DP/ASi Link

Отзывы:

Бренды по названию

Популярные бренды