manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Руководство пользователя

Поделиться
Скачать
Siemens SIMATIC Distributed I/O System DP/ASi Link Скачать руководство пользователя страница 14

1-2

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

1.1

Using the DP/ASi Link

The DP/ASi link connects the Actuator Sensor Interface (referred to in the
following as ASi) to the PROFIBUS-DP.

PROFIBUS-DP conforms to the PROFIBUS-DP standard EN 50170 Vol-
ume 2, PROFIBUS; the term DP means ”distributed I/O”.

You will find an explanation of how the ASi works in Chapter 2.

Sensor

Actuator

DP/ASi

link

Lowest level

DP master

Higher level

PROFIBUS-DP

ASi

Sensor

Actuator

DP

slave

Figure 1-1

Integrating the DP/ASi link

Up to 31 binary actuators and sensors are networked over the ASi cable. The
DP/ASi link is used to interface the ASi cable to PROFIBUS-DP. You can
operate up to 122 DP/ASi links to PROFIBUS-DP, should you use the
IM 308-C, for example, as the DP master.

ASi allows one ASi master. The DP/ASi link is the ASi master.

The DP/ASi link meets the IP 66/IP 67 degree of protection.

Owing to the IP 66/IP 67 degree of protection, you can use the DP/ASi link in
a harsh industrial environment. There is no preferred mounting location for
the DP/ASi link.

Definition

ASi and PROFI-
BUS-DP

Explanation

ASi master

IP 66/67

Installation

Overview

Содержание SIMATIC Distributed I/O System DP/ASi Link

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды