Siemens SIMATIC Distributed I/O System DP/ASi Link Скачать руководство пользователя страница 55

Страница: 55 / 152

4-19

Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b

4.4.4

Cables

The PROFIBUS-DP features different installation options, for which you
need the correct cables. There are the following types of cables.

Table 4-5

PROFIBUS-DP cables

No. of

Cores

Usage

PROFIBUS-DP field bus, power supply is not incorporated

For PROFIBUS-DP field bus and power supply in one
cable

For power supply feed line to the power supply connector

SIEMENS supplies cables for the PROFIBUS-DP in different designs.

All cables are precut with connectors at both ends, at one end or not at all
with a 12-pin connector for connection to the PROFIBUS-DP bus and/or
power supply.

You can cut the cables and fit connectors yourself. You will find the neces-
sary information in section 4.4.7.

Note

All precut cables fitted with connectors are designed with a core cross-sec-
tion of 0.75 mm

for a current loading not exceeding 4 A.

You have to precut the cable for the power supply feed line for a separate
power supply and fit the connectors yourself.

Types of cables

Designs

Installing and Wiring the DP/ASi Link

Содержание SIMATIC Distributed I/O System DP/ASi Link

























































































































































Результаты поиска

Содержание SIMATIC Distributed I/O System DP/ASi Link

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC Distributed I/O System DP/ASi Link, Руководство пользователя

Результаты поиска

Содержание SIMATIC Distributed I/O System DP/ASi Link

Отзывы:

Бренды по названию

Популярные бренды