manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Руководство пользователя

Поделиться
Скачать
Siemens SIMATIC Distributed I/O System DP/ASi Link Скачать руководство пользователя страница 28

3-2

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

3.1

Summary

 

of

 

Configuration Options

PROFIBUS-DP presents you with different configuration options for combin-
ing the PROFIBUS-DP and the 24 V power supply of the devices. The fol-
lowing Table 3-1 shows the different options.

Table 3-1

Configuration options 

Power Supply Connector for Device’s

Internal Power Consumption

Configuration

Refer to

Configuration with power supply con-

Configuration without T connector

Section 3.2

g

p

pp y

nector

Configuration with T connector

Section 3.3

Configuration with programmer
connector

Section 3.6

Configuration with several power supply connectors (the degree of expansion is
limited with a PS connector)

Section 3.4

Configuration without power supply
connector (every L2 station has a sepa-

Configuration without power supply con-
nector

Section  3.5

(

y

p

rate power supply)

Configuration with programmer
connector 

Section 3.6

Configuration options are described in the following using illustrations for a
possible installation. We use the following legend:

PS

PS

cntr

T connector

Power supply connector

Programmer connector

Bus cable

Power supply (PS) cable

Bus cable incl. PS cable

Adapter cable

2-core

5-core

3-core (see note)

PG

Terminating resistor

Figure 3-1

Legend

Note

The 2-core bus cable must not be incorporated between the power supply
unit and a load.

If you incorporate the bus cable in the power supply cable, an inadmissible
spur line occurs. Data transfer is no longer assured in the PROFIBUS-DP.

Configuration
options

Legend for
following sections

Configuration Options

Содержание SIMATIC Distributed I/O System DP/ASi Link

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды