Siemens SIMATIC Distributed I/O System DP/ASi Link Скачать руководство пользователя страница 35

Страница: 35 / 152

3-9

Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b

3.6

Configuration with Programmer Connector

If you wish to operate the programmer on the PROFIBUS-DP in an
IP 66/IP 67 environment, you require a programmer connector.

To connect the programmer to the programmer connector, you require two
plug-in connectors:

adapter cable

programmer connecting cable

An ET 200 Handheld cannot be connected to the programmer connector. The
ET 200 Handheld can be plugged only into the bus connection of a slave sta-
tion (using the adapter cable).

Fig. 3-8 shows a possible installation for the configuration with a program-
mer connector.

DP/ASi link

External
power supply

PROFIBUS-DP

cntr.

Adapter cable

Programmer
connecting
cable

IP 66/IP 67 world

IP 20 world

DP/ASi link

Figure 3-8

Configuration with programmer connector

Definition

Connecting the
programmer

Installation

Configuration Options

Содержание SIMATIC Distributed I/O System DP/ASi Link

























































































































































Результаты поиска

Содержание SIMATIC Distributed I/O System DP/ASi Link

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC Distributed I/O System DP/ASi Link, Руководство пользователя

Результаты поиска

Содержание SIMATIC Distributed I/O System DP/ASi Link

Отзывы:

Бренды по названию

Популярные бренды