Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 77

Страница: 77 / 130

Service and maintenance

7.4 Warranty

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

7.4

Warranty

Procedure

Note
Loss of warranty

If you open the device, you will invalidate the Siemens warranty. Only the manufacturer is

permitted to carry out repairs to the devices. Return faulty or damaged devices to Siemens for

repair or replacement.

If the device is faulty or damaged, proceed as follows (only during the warranty period):
1.

Uninstall the device; refer to section Removal (Page 38).

Pack the device in a suitable manner to prevent it from being damaged during transport.

Return the device to Siemens. You can obtain the address from:

–

Your Siemens sales partner

–

Technical Assistance

Note

The contents of this manual shall not become part of or modify any prior or existing

agreement, commitment, or contractual relationship. All Siemens obligations derive from the

respective sales contract, which also contains the complete and exclusive warranty

agreement. These contractual warranty requirements are neither extended nor restricted by

the implementation of this Operating Manual.

See also

Latest information (Page 7)

Disposal of waste electronic equipment

Waste electronic equipment must not be disposed of as unsorted municipal waste, e.g.

household waste. When disposing of waste electronic equipment, the current local

national/international regulations must be observed.

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 77 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: