Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 130

Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 66

Commissioning

6.3 Parameterizing the device

PAC2200CLP

64

Equipment Manual, 06/2021, L1V30820585B-02

"Basic settings" parameter

Not available for 65 A devices.

"Current input" parameter

The "Current input" parameter specifies the values for the current input.
When measuring via current transformer, the device must know the current conversion ratio.
For this purpose, the primary and secondary current must be specified in the fields "PRIMARY

CURRENT" and "SECONDARY CURRENT".

Selection

Range

Factory setting

PRIMARY CURRENT

Freely adjustable.

Range: 1 A ... 10000 A

50 A

SECONDARY CURRENT Range: 1 A, 5 A

5 A

DISPLAY RANGE

Freely adjustable.

Range: 1 A ... 10000 A

50 A

I(n) display

Display of current in neutral conductor (calculated)

No:

•

Neutral current is displayed in menu item 3.0

Yes:

•

Neutral current is not displayed

Yes

You can configure the resolution of the current display in the "DISPLAY RANGE" menu item.

The setting has no impact on the measurement accuracy of the device. The recommended

setting is the current that is usually flowing in the system. If the usual current is 50 A, set the

display range to 50 A. In this case, the current is displayed with one decimal place.

"Write protection" parameter

The "Write protection" parameter is described later in this chapter.

«
...
64
65
66
67
68
...
»

Содержание SENTRON PAC2200CLP



































































































































Отзывы:

Нет отзывов