Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 70

Страница: 70 / 130

Commissioning

6.3 Parameterizing the device

PAC2200CLP

Equipment Manual, 06/2021, L1V30820585B-02

Selection

Range

Factory setting

UNIT

Selects the type of cumulative power and the import

value that triggers the pulse when that value is

reached.
•

Counter Import Active Energy (kWh)

•

Counter Export Active Energy (kWh)

•

Counter Import Reactive Energy (kvarh)

•

Counter Export Reactive Energy (kvarh)

Counter Import

Active Energy

(kWh)

PULSE LENGTH

The "Output pulse divider" property is only visible if

"Energy pulse" is set for the "USAGE TYPE".

Length of energy pulses.

Range: 30 ms to 500 ms

100 ms

"Communication" parameter

The number of available communications interfaces can vary depending on the version of the

device.

"MODBUS TCP" parameter

Selection

Range

Factory setting

MAC

MAC address. Read only.

–

DHCP

(Dynamic Host Configuration Protocol)

OFF

If the DHCP is activated, network configurations are

automatically assigned. This enables automatic inte-

gration of devices in an existing network. If the DHCP is

activated, network configurations cannot be adjusted

manually.

IP address: 000.000.000.000

Manual setting of the IP address is only possible when

DHCP is deactivated.

–

(subnet mask)

Subnet address: 000.000.000.000

Manual setting of the subnet is only possible when

DHCP is deactivated

–

LIMIT

(gateway)

Gateway address: 000.000.000.000

If data exchange with an IP address which is not in the

home subnet is required, the data can be transmitted

via a gateway. Gateway interconnects different net-

works.

Manual setting of the gateway is only possible when

DHCP is deactivated.

–

PORT

Modbus port: 0 to 65534

502

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 70 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: