Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 23

Страница: 23 / 130

Description

2.3 Functions for delimiting third-party quantities according to §62b Par. 1 of the Renewable Energy Act

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

Date:

Shows the date currently set in the device.

Format:

Format used for display.

Time:

Shows the time currently set in the device.

Time zone:

This must be set correctly here based on the geographical time zone. It is a

prerequisite for correct time synchronization.

Daylight saving:

The setting which applies to the place of installation must be entered here.

Option

Description

Auto EU

Usual setting for Europe

Auto US

Usual setting for USA

Off

Time change is deactivated

Table

For specifying custom definitions. Requires the powerconfig configuration soft-

ware V3.17 or higher, which is available free of charge.

Example of configuration for Germany:
•

Time zone: +01:00

•

Daylight saving: Auto EU

SNTP:

Option

Description

Active

The device continually polls the configured IP address of the SNTP server to effect

synchronization (recommended setting).

BCST client

The device receives the broadcasts of an SNTP server which actively distributes

these to all the subscribers in the network. Only broadcasts from the configured

IP address are accepted. If the IP address setting remains unchanged at 0.0.0.0,

every broadcast is accepted.

Off

Synchronization via SNTP is deactivated.

IP:

IP address of SNTP server. If the address configuration of the device takes place via DHCP, the

IP address of the SNTP server is automatically assigned as a rule.
If an IP address was entered manually, this address is used.

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 23 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: