Siemens OZW775 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 120

background image

49/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

5.6.1 RXB/RXL

device

address

with QAX34.3 room unit

The QAX34.3 room unit covers all the standard room unit functions. The room unit
can also be used to set the RXB/RXL room controller parameters via PPS2.

The QAX34.3 room unit is not suitable for direct connection to the KNX bus.

The tool socket (RJ45) on the RXB/RXL room controllers serves as a PPS2
interface and a bus interface (CE+ und CE-). This tool socket can be used to
connect room units (PPS2), the OCI700 service interface or the RMZ792 bus
operator unit.

•

Physical address (network address)

•

Zones (for communication in LTE mode)

•

Setpoints

•

Master/slave settings

•

All parameters (refer to the detailed in formation in document CM110385)

Group addresses (bindings) cannot be assigned. This must be carried out with the
ETS.

Function of the buttons

10

3

8

5Z7

0

+

= Count/move upward

–

= Count/move downward

>

= Esc

(exit without confirmation)

<

= Enter

(confirm/acknowledge)

Restart

After significant parameter changes, the room
controller is restarted

"Minor parameter setting", with access in parameter mode is sufficient for setting
the device address or complete network address:

•

Hold down the

<

,

>

and

–

buttons simultaneously for approximately 2 s until the

display turns dark (no values displayed).

•

Then briefly press the

–

button twice in succession.

•

The display now reads 0 (mode 0).

•

The following modes can be selected with the

+/–

buttons:

0

= Normal

mode (normal room unit functions).

2

= Display mode:

The parameter display is prefaced with the letter "d", e.g.

d 15

.

Use

+/–

to find the required number and acknowledge with

<

(Enter).

The relevant value is then displayed.
Press

<

(Enter) or

>

(Esc) to return to the list.

3

= Parameter mode

Start the parameter mode by pressing

<

(Enter), enabling the parameter

numbers to be selected and the parameter values to be set. Parameter
numbers are preceded by the letter "P", e.g.

P 2

.

Notes

Parameter setting

Minor parameter setting

Major parameter setting

Note

Minor parameter setting

«
...
47
48
49
50
51
...
»

Содержание OZW775

























































































































Отзывы:

Нет отзывов

Похожие инструкции для OZW775

ElectraElite IPK

Бренд: NEC Страницы: 20

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Innovative Technology Страницы: 14

Бренд: Goodmans Страницы: 22

Бренд: jWIN Страницы: 13

Бренд: Jensen Страницы: 41

Бренд: Hioki Страницы: 52

Бренд: Carel Страницы: 94

Enado Mini ENA-MINI-010

Бренд: Wyrestorm Страницы: 2

Бренд: B&R Industries Страницы: 16

Бренд: Marshall Amplification Страницы: 30

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 24

DOCKCONTROLLER DC-200

Бренд: Motorola Страницы: 16

Бренд: HP Страницы: 174

Бренд: Bosch Страницы: 252

Бренд: Pioneer Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды