Siemens OZW775 Скачать руководство пользователя страница 4

Страница: 4 / 120

4/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Contents

30.08.2007

5.1.5

Addressing devices with the OCI700.1 service tool.................................37

5.2

RM… controller device address ...............................................................38

5.2.1

Assigning addresses manually.................................................................38

5.2.2

Assigning addresses automatically ..........................................................39

5.2.3

Assigning addresses in programming mode............................................40

5.2.4

Addressing via the ID number..................................................................41

5.3

Device address for the OZW771.xx central communication units ...........42

5.3.1

Other addressing options, OZW771.xx....................................................43

5.3.2

Restoring the factory settings, OZW771.xx .............................................43

5.4

Device address for the OZW775 central communication unit..................44

5.5

Device address for the QAX910 central apartment unit...........................45

5.6

Device address for the RXB/RXL room controllers ..................................48

5.6.1

RXB/RXL device address with QAX34.3 room unit .................................49

5.7

Device address for the QAW740 room unit..............................................51

5.8

Device address for RMZ792 bus operator unit ........................................53

5.9

Addressing the couplers...........................................................................56

5.9.1

Line couplers ............................................................................................56

5.9.2

Area couplers ...........................................................................................58

5.10

Addressing the IP router ..........................................................................59

5.10.1

KNX network address ..............................................................................59

Basic communication settings .............................................................61

6.1

RM… controllers.......................................................................................61

6.1.1

Decentral bus power ................................................................................61

6.1.2

Clock time operation ................................................................................61

6.1.3

Setting a time slave remotely ...................................................................62

6.1.4

Remote reset of fault ................................................................................64

6.2

Basic settings via ACS .............................................................................65

Communication via zone addresses ....................................................67

7.1

General notes on zones ...........................................................................67

7.1.1

Synco zoning............................................................................................67

7.1.2

Communication of process values ...........................................................68

7.1.3

Geographical zone (apartment) ...............................................................69

7.1.4

Default "----" in series B devices ..............................................................70

7.2

Zone addressing with the RMZ operator units .........................................72

7.2.1

RM… controllers.......................................................................................72

7.2.2

QAWZ740 room unit.................................................................................73

7.3

Addressing the zones with ACS ...............................................................74

7.3.1

RM… controllers.......................................................................................74

7.3.2

RXB/RXL room controllers .......................................................................75

7.3.3

Zone addressing with the QAX34.3 room unit .........................................75

Содержание OZW775

























































































































Результаты поиска

Содержание OZW775

Отзывы:

Похожие инструкции для OZW775

Бренды по названию

Популярные бренды

Siemens OZW775, Основная документация

Результаты поиска

Содержание OZW775

Отзывы:

Похожие инструкции для OZW775

Бренды по названию

Популярные бренды