Siemens OZW775 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 120

background image

38/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

5.2

RM… controller device address

The Synco 700 devices are factory-set with device address 255. This address must
be changed to allow communication via the KNX bus. The address can be modified
in different ways with ACS Service (see further below).

For information about the various RM… controllers, refer to the associated data
sheets and basic description documents (for details see section 1.2).

The RM… controllers can supply power to the KNX bus.

For communication purposes, the RM… controllers can be operated with the
setting "Decentral bus power supply = On". Alternatively a central bus power
supply must be available (see section 2.2).

5.2.1

Assigning addresses manually

With ACS service and manually assigned addresses, the Synco 700 devices,
RXB/RXL room controllers, OZW77x central communication units and Synco 900
type QAX910 central apartment units can be allocated a device address and a
device name.

1.

In ACS Service select

Plant > Edit device list…

to open the "Edit device list" dialog

box.

2. Select the required device with the left mouse button.

3. Click

Manually…

to open the "Address assignment" dialog box.

4. Enter a device address in the range 1…253 (excluding 150), and confirm by

clicking the

Write

button.

Introduction

Note

Bus power supply

Procedure

«
...
36
37
38
39
40
...
»

Содержание OZW775

























































































































Отзывы:

Нет отзывов

Похожие инструкции для OZW775

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 33

Бренд: TANDBERG Страницы: 12

Magnavox FW 55C

Бренд: Magnavox Страницы: 80

Бренд: Estun Страницы: 41

Бренд: ATEN Страницы: 176

Бренд: ION Страницы: 48

Бренд: Roadstar Страницы: 23

Varixx UMS 4401 SPCD

Бренд: Grundig Страницы: 47

Бренд: SEW-Eurodrive Страницы: 384

Бренд: Taiden Страницы: 91

Бренд: Aiwa Страницы: 28

TorqueTrak Revolution

Бренд: Binsfeld Страницы: 2

Бренд: Yealink Страницы: 6

Бренд: Oakcastle Страницы: 25

Бренд: Sony Страницы: 7

Бренд: Sony Страницы: 12

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды