Siemens OZW775 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 120

background image

21/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Engineering notes

30.08.2007

2.2.3

Central bus power supply

When one or more power supply units (PSU) are used for the bus power supply,
this is referred to as a "central bus power supply". This type of bus power supply is
required in the following circumstances:

•

The permitted 8 Synco devices with DPSU (Decentral bus power supply = On")

are insufficient to cover the power consumption of the devices without a bus
power supply.

•

Synco devices and third-party devices are installed on the same line.

•

Only devices without a bus power supply are installed on the same line.

On a line with a central bus power supply, the following devices must not be used
to supply power to the bus:

•

RM…controllers

•

OZW775 central communication unit

•

QAX910 central apartment unit

These Synco devices must be set to "Decentral bus power supply = Off" to prevent
them from interfering with bus communications.

Power supply units for

160,

320

and

640 mA

are available. The power consump-

tion of the devices must be calculated as a means of determining the required
power supply unit, PSU (see the relevant values on the previous page).

For a line accommodating 64 bus devices, each with a power consumption of 5 mA
(64 x 5 mA = 320 mA), a power supply unit of 320 mA is sufficient.

The following power supply units from Siemens are recommended for KNX
networks (see also "GAMMA building management system").

Order codes:

•

5WG1 125-1AB01, short code N125/

01

160 mA

(with integrated choke)

•

5WG1 125-1AB11, short code N125/

11

320 mA

(with integrated choke)

Product data:

•

Operating voltage

AC 120…230 V, 50…60 Hz

•

Bus voltage output

DC 29 V (21…30 V, with choke)

For KNX networks with IP routers, the following Siemens power supply unit is
recommended.

Order code:

•

5WG1 125-1AB11, short code N125/

21

640 mA

Product data:

•

Operating voltage

AC 120…230 V, 50…60 Hz

•

Bus voltage output

DC 29 V (21…30 V, with choke)

•

Output, auxiliary voltage for IP router

DC 24 V (12…30 V, without choke)

For further information refer to the product description and description of functions
(enclosed with the device) or:

www.automation.siemens.com/et/gamma/

DC 29 V voltage with choke is required for the bus power supply. The DC 24 V
auxiliary voltage for the IP router requires a voltage source without choke.

Introduction

Note

Power supply unit, PSU

Siemens power supply
units

Note

«
...
19
20
21
22
23
...
»

Содержание OZW775

























































































































Отзывы:

Нет отзывов

Похожие инструкции для OZW775

Бренд: Magnavox Страницы: 26

Бренд: Union Instruments Страницы: 63

Бренд: Woodward Страницы: 112

Бренд: Daewoo Страницы: 21

Бренд: Optimus Страницы: 44

Бренд: Carel Страницы: 2

Бренд: Edis Страницы: 39

Bell'O Digital BDSW-1650-BLK

Бренд: Twin-Star International Страницы: 20

Бренд: LENCO Страницы: 66

Бренд: L.J. Wing Страницы: 60

ClickShare CX-20 Gen2

Бренд: Barco Страницы: 66

Бренд: Balboa Water Group Страницы: 20

Бренд: Curtis Страницы: 1

Бренд: Fujitsu Страницы: 8

Бренд: Philips Страницы: 2

SAAK630 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 16

SAAK320 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 20

SAAK600 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды