Siemens OZW775 Скачать руководство пользователя страница 80

Страница: 80 / 120

80/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Large plants

30.08.2007

KNX network with third-party devices in Area 15

1.2.1

1.1.1

RM...

1.1.2

RM...

1.1.250

RM...

1.2.2

RM...

1.2.250

RM...

1.15.1

RM...

1.15.2

RM...

1.15.250

RM...

N140/13

1.0.1

RM...

1.0.2

1.0.250

Bereich 0

0.2.150

OZW775

2.0.1

RMB...

2.0.10

RX...

2.0.20

RX...

2.0.250

N140/13

0.2.254

-12 °C

N140/13

N125/x1

15.0.10

Dimmer

15.0.20

N140/13

15.1.10

0.2.252

RMZ792

15.0.1

AC 120...230 V

N125/x1

15.1.1

AC 120...230 V

ne 1

ne 2

ne 15

Main line 1

ACS alarm

pager, SMS, fax

Mai

ine

PC with ACS

Service cable

RJ45

connector

Bus connector

socket

Bus power supply

Input and
display unit

ne 1

Main line 15

Switch
actuator

Bus power supply

Switch
actuator

Ac 1.0.0

Ac 2.0.0

Ac 15.0.0

Lc 1.1.0

Lc 1.2.0

Lc 1.15.0

Lc 15.1.0

LTE filter table: 1) Normal (route), 2) Route all, 3) Block all

If the filter is set to "Block all" for area coupler Ac 15.0.0, no LTE telegrams are
transmitted between area 15 and the rest of the network.

The "Route all" setting for line coupler Lc 15.1.0 means that there is no filtering
between line 15.1 and main line 15.

If the devices in area 15 (e.g. third-party products) do not supply power to the bus,
an N125/x1 power supply unit must be installed in each line (main line 15, line 15.1
plus further lines 15.x, if applicable) for the bus power supply.

Example 3

LTE filter table

Bus power supply

Содержание OZW775

























































































































Результаты поиска

Содержание OZW775

Отзывы:

Похожие инструкции для OZW775

Бренды по названию

Популярные бренды

Siemens OZW775, Основная документация

Результаты поиска

Содержание OZW775

Отзывы:

Похожие инструкции для OZW775

Бренды по названию

Популярные бренды