Siemens OZW775 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 120

background image

64/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Basic communication settings

30.08.2007

6.1.4

Remote reset of fault

The "Remote reset of fault" function is used to reset the Synco 700 RM… controller
faults transmitted over the KNX bus and requiring "Acknowledgement and reset", to
be acknowledged (and reset if "Remote reset fault: Yes") with the OCI700.1 service
tool, the RMZ792 bus operator unit and the OZW775 central communication unit.

Main menu > Commissioning > Communication > Basic settings

Remote reset faults for the RM… controllers

Default.

No

Settings

No/Yes

Apart from the RMH760 heating controller, all RM… controllers (including the
RMH760B heating controller) incorporate the "Remote reset of fault" function.

RM… controllers

Note

Basic settings

Dec bus power supply: On

Clock time op: Slave

Rem set clock save: Yes

Remote reset fault: Yes

«
...
62
63
64
65
66
...
»

Содержание OZW775

























































































































Отзывы:

Нет отзывов

Похожие инструкции для OZW775

Бренд: iDance Страницы: 25

TVNext NN01-054

Бренд: Fractus Antennas Страницы: 14

Бренд: GSK Страницы: 32

Бренд: Dual Electronics Corporation Страницы: 16

CIRFLEXX UMS 4100

Бренд: Grundig Страницы: 38

Бренд: Laser Страницы: 3

Бренд: Easun Страницы: 6

Бренд: Advantech Страницы: 82

Бренд: Woodward Страницы: 84

Бренд: Teac Страницы: 16

Бренд: babala Страницы: 30

Бренд: Nexus Страницы: 97

Бренд: RCA Страницы: 19

Бренд: Avalon Страницы: 86

Бренд: Cisco Страницы: 4

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды