Siemens NK8237 IEC 60870-5-104 Скачать руководство пользователя страница 26

Страница: 26 / 80

Hardware installation
NK8237 hardware installation

26
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

WARNING

There is a risk of explosion if the battery is replaced with an incorrect battery type.

Use 27Ah 12V batteries. Dispose of the used battery at a recycling point in

accordance with the local environmental standards and regulations.

X103: Power Supply

Power connections.

Power supply

Assignment

Primary

Earth

–

N/A

Not used

N/A

Not used

Secondary

(optional)

Earth

–

X2/X3: Ethernet Connector

A standard RJ45 connector connects Ethernet. Category 5 or 6 UTP cabling is best

suited.

Ethernet connections.

Assignment

TX+

–

RX+

n.c.

–

n.c.

X101: Onboard I/O (Output Relay)

Onboard I/O (output relay).

Assignment

Common

NO output

NC output

Содержание NK8237 IEC 60870-5-104

















































































Результаты поиска

Содержание NK8237 IEC 60870-5-104

Отзывы:

Похожие инструкции для NK8237 IEC 60870-5-104

Бренды по названию

Популярные бренды

Siemens NK8237 IEC 60870-5-104, Установка, настройка и ввод в эксплуатацию

Результаты поиска

Содержание NK8237 IEC 60870-5-104

Отзывы:

Похожие инструкции для NK8237 IEC 60870-5-104

Бренды по названию

Популярные бренды