Siemens Flender KMP Series Скачать руководство пользователя страница 5

Страница: 5 / 84

5 / 84

BA 9142 en 02/2015

Contents

Technical data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1

General technical data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2

Measuring-surface sound pressure level

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3

List of equipment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1

Obligations of the user

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

Special dangers and personal protective equipment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3

The five safety rules

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4

Environmental protection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Transport and storage

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1

Content and check of the scope of delivery

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2

Transport

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3

Storing the gear unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4

Standard coating and corrosion prevention

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.1

Exterior preservation of metallic bright exterior surfaces

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.1.1 Maximum durability period of the exterior preservation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.1.2 Prolongation of the preservation of metallic bright exterior surfaces of the gear unit

. . . . . . . . . . .

4.4.2

Preservation of the interior of the gear unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.2.1 Maximum durability period of the interior preservation of the gear unit

. . . . . . . . . . . . . . . . . . . . . . .

4.4.2.2 Combined storage/packaging

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.3

Renewal of the interior preservation of the gear unit for longer periods of storage of the
gear unit that has not been taken into operation yet

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.3.1 Renewal of the gear unit interior preservation with "Castrol Corrosion Inhibitor N 213"

. . . . . . . . .

4.4.3.2 Renewal of the gear unit interior preservation through complete filling with preservative

or operating oil

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.3.3 Renewal of the interior preservation of the gear unit using the oil-supply system

. . . . . . . . . . . . . .

Technical description

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1

General description

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2

Delivery condition of the gear unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3

Lubrication

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3.1

Hydrodynamic lubrication of the axial tilting pad thrust bearings

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3.2

Hydrodynamic lubrication of the axial tilting pad thrust bearings in gear units
with hydrostatic start-up assistance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3.3

Hydrodynamic lubrication of the axial tilting pad thrust bearings with radial piston pump

. . . . . . .

5.3.4

Labyrinth seals

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4

Drive coupling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5

Heating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6

Indication of oil level

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7

Oil temperature monitoring

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание Flender KMP Series





















































































Результаты поиска

Содержание Flender KMP Series

Отзывы:

Похожие инструкции для Flender KMP Series

Бренды по названию

Популярные бренды

Siemens Flender KMP Series, Руководство по сборке и эксплуатации

Результаты поиска

Содержание Flender KMP Series

Отзывы:

Похожие инструкции для Flender KMP Series

Бренды по названию

Популярные бренды