Siemens Flender KMP Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 84

background image

BA 9142 en 02/2015

4.

Transport and storage

Observe the instructions in section 3. "Safety instructions"!

4.1

Content and check of the scope of delivery

The content of the delivery is listed on the packing slip. The completeness of the scope of delivery must
be checked against the packing slip directly on receipt. The packaging must not be opened for the check.
Damages on packaging and/or items missing from the package must be reported to Siemens in writing
within 2 weeks.

NOTICE

Property damage

Damage to the gear unit from corrosion is possible.
The packaging must not be opened in any case. Otherwise, the durability period of the gear unit
preservation will reduce.

Note

If the packaging is opened nonetheless, section 4.4 must be observed.

WARNING

Serious personal injury can be caused by a defective product

If there is any visible damage, the gear unit must not be taken into operation.

4.2

Transport

Note

The product weight is indicated on the rating plate.

DANGER

Danger to life

Danger to life from load falling down due to deficient attachment.
Do not stay underneath suspended loads.
When attaching, lifting, lowering and shifting the load, pay attention to the following:
– Observe the load limits.
– Proper fastening of the attachment equipment.
– Centre of gravity possibly being off centre.
– Even load distribution on load-bearing equipment with multiple load hook-ups.
– Low process speed.
– Oscillating the load and/or attaching the load to objects

or building parts is prohibited.

– Load hooks may not be loaded at their tip.
– Set down products only on even, non-slipping and stable underground.

«
...
12
13
14
15
16
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: Canta Страницы: 2

Бренд: B&G Страницы: 3

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: Cadex Страницы: 300

Бренд: Idmed Страницы: 2

Бренд: Macht Dental Страницы: 8

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: Yacht Devices Страницы: 32

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

Бренд: Tarter Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды