Siemens Flender KMP Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 84

background image

BA 9142 en 02/2015

4.4

Standard coating and corrosion prevention

The gear unit is to be provided with interior preservation on delivery (see "Technical data" in the gear unit
documentation prepared specifically for the order), and the free shaft ends are to be provided with
protective preservation (see Table 1 in item 4.4.1.1).

The properties of the exterior preservation when using the Siemens standard priming are resistant to:

─

weak acids and alkalis,

─

solvents,

─

weathering, also tropical weathering

─

temperatures up to 120 °C / 248 °F (for short periods up to 140 °C / 284 °F)

If a different exterior coating is intended by the customer (contrary to the Siemens standard), the protection
of the external coating will be within the customer's responsibility.

NOTICE

Property damage

Damage to the gear unit from corrosion is possible.
The gear unit is normally delivered completely ready with a priming and a finishing coat.
Where gear units are delivered with a priming coat only, it is necessary to apply a finishing coat
according to the standard procedures relevant for the specific application.
The priming coat alone is not suitable to provide sufficient long-term corrosion protection.

Note

Corrosion prevention durations of the interior preservation depend on the kind of transport, type of
packaging and the place of installation and/or storage (see Table 2 in item 4.4.2.1).
The durability period of the exterior preservation and the related requirements can be found in Table 1
under item 4.4.1.1.
The warranty starts upon notification of readiness for delivery (see "Technical data" in the gear unit
documentation). The provided interior gear unit preservation is also shown in "Technical data".

When storing differently from the durability periods of preservation as specified in Tables 1 and 2
applicable for the gear unit, the interior preservation must be prolonged (see item 4.4.3) and if necessary,
the exterior preservation must be renewed (see item 4.4.1)

.

Each prolongation of the interior preservation and any renewal of the exterior preservation must be logged.

Note

The record must be kept with these instructions.

«
...
16
17
18
19
20
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: ABB Страницы: 6

Бренд: Bartscher Страницы: 22

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Бренд: 3M Страницы: 48

Бренд: 3M Страницы: 19

Speedglas G5-01

Бренд: 3M Страницы: 62

Quickfit Nexus Exit

Бренд: Thomas & Betts Страницы: 2

Бренд: Vahle Страницы: 96

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренд: B medical systems Страницы: 28

Бренд: Radial Engineering Страницы: 16

Бренд: R&S Страницы: 61

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: Ganter Norm Страницы: 20

TRAKTOR KONTROL S3

Бренд: Native Instruments Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды