Siemens Flender KMP Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 84

background image

BA 9142 en 02/2015

3.

Safety instructions

WARNING

Risk of falling

Serious injury from falling is possible.
The gear unit and its add-on parts must not be accessed during operation.
The gear unit may only be accessed for maintenance and repair works during standstill of the gear unit.

WARNING

Risk of injury from changes made on own initiative

Changes made on own initiative are prohibited.
This also pertains to the protection equipment that is installed as contact protection.

3.1

Obligations of the user

•

The operator must ensure that everyone carrying out work on the gear unit has read and understood
these instructions and is adhering to them in every point in order to:

─ avoid injury or damage to the user and third parties,

─ ensure the safety and reliability of the gear unit,

─ avoid loss of use and environmental damage caused by incorrect use.

•

During transport, assembly, installation, demounting, operation and maintenance of the unit, the
relevant safety and environmental regulations must be observed at all times.

•

The gear unit may only be operated, maintained and/or repaired by persons qualified for the work
concerned (see "Qualified personnel" on page 3 of this manual).

•

The outside of the gear unit must not be cleaned with high-pressure cleaning equipment.

•

All work must be carried out with great care and due regard for safety.

DANGER

Danger to life from switched on system

For carrying out work on the gear unit, the gear unit and an added on or separate oil-supply system must
generally be set in standstill.
The drive unit must be secured against accidental start-up (e. g. by locking the key switch or removing
the fuses from the power supply).
Attach a notice on the start switch stating clearly that work is in progress on the gear unit.
At the same time, the complete system must be free from load so that no danger is caused during the
disassembly work.

•

No welding work may be done at all on the drive.
The drive systems must not be used as an earthing point for electrical welding works. Toothed parts
and bearings can be irreparably damaged by welding.

«
...
8
9
10
11
12
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: KaVo Страницы: 16

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: TAIKO Audio Страницы: 24

Бренд: Ultimaker Страницы: 38

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: QBC Diagnostics Страницы: 65

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды