Siemens Flender KMP Series Скачать руководство пользователя страница 63

Страница: 63 / 84

63 / 84

BA 9142 en 02/2015

Fig. 9:

Gear unit features for preservation measures

Ventilation sealing cap

Oil drain sealing cap

Sealing cap

Air filter (gear unit)

Oil level indicator (gear unit)

Suction line (gear unit)

Oil drain (gear unit)

Pressure line (gear unit)

Pressure line (tilting pad thrust bearing
chamber)

Oil drain (tilting pad thrust bearing
chamber)

Air filter (tilting pad thrust bearing
chamber)

Oil level indicator (tilting pad thrust
bearing chamber)

Round cord hollow profile

•

Replace the air filter of the tilting pad thrust bearing chamber (11) with a screw plug
(at start-up, the screw plug must be replaced for the air filter again).

•

The lower oil drain cock on the gear unit (7) must be provided and sealed with a screw plug.

•

If not already done beforehand, close ventilation of the sealing cap (1).

NOTICE

Property damage

Corrosion is possible when the gear unit is opened for too long.
Close the gear unit airtight again, at the latest one hour after complete filling.

Note

Before restarting the gear unit, the measures according to section 7.1 and 7.2 have to be carried out.

7.3.2

Exterior corrosion prevention

•

Clean the surfaces.

•

Apply preservative agent.

Note

Preservative agent, see Table 1 in item 4.4.1.1.

Содержание Flender KMP Series





















































































Результаты поиска

Содержание Flender KMP Series

Отзывы:

Похожие инструкции для Flender KMP Series

Бренды по названию

Популярные бренды

Siemens Flender KMP Series, Руководство по сборке и эксплуатации

Результаты поиска

Содержание Flender KMP Series

Отзывы:

Похожие инструкции для Flender KMP Series

Бренды по названию

Популярные бренды