Siemens Flender KMP Series Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 84

background image

BA 9142 en 02/2015

7.3.1

Renewal of the gear unit interior preservation on gear units having already been in operation

Depending on the specific application, the following measures for renewing the interior preservation of the
gear unit can be taken in case it is taken out of service for a longer period (> 7 days).

The durability period of this preservation kind depends on the measure for renewing the interior
preservation of the gear unit, the packaging type, and the setup and/or storage place (see Table 11 or
Table 12 in item 7.3.1.1).

Definition of climatic zones:

A

A

B

North Pole 90°N

South Pole 90°S

Arctic Circle 66.5°N

Antarctic Circle 66.5°S

Northern Tropic 23.5°N

Southern Tropic 23.5°S

Equator 0°

7.3.1.1 Renewal of the interior preservation of the gear unit using the oil-supply system

The prerequisite for this is that the gear unit is still below the mill and connected to the oil-supply system.
"Castrol Alpha SP 220 S" or "Tribol1390" can be used as preservative agent. The oil level must never be
below the MIN mark on the oil level indicator of the main gear unit, the tilting pad thrust bearing chamber
and/or the oil-supply system (if the model has a tank). See also operating instructions of the oil-supply
system. For this purpose, turn on the oil-supply system and turn the gear unit without load (at least
1 rotation on the output). Drain the oil, close, mask and seal the gear unit and oil-supply system airtight.
Replace air filters for sealing caps and be seal them. Seal the gear unit airtight with a round cord hollow
profile between the gear unit housing and the output flange. Mask the labyrinth seals on the input shaft and
on the output flange airtight within 1 hour.

Note

Clean the air filters thoroughly (see item 10.3) and keep it in a safe place (these will be required when
starting up again).

«
...
56
57
58
59
60
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: B&K Страницы: 12

Бренд: TAIKO Audio Страницы: 24

Бренд: Bacharach Страницы: 48

Бренд: p-light Страницы: 28

Бренд: HANYOUNG NUX Страницы: 2

Бренд: YOKOGAWA Страницы: 75

Бренд: Y.I.C. TECHNOLOGIES Страницы: 6

Бренд: Veit Brisay Страницы: 18

Бренд: Bavis Страницы: 8

Бренд: Flex-A-Seal Страницы: 7

Бренд: Topcon Страницы: 38

Бренд: Softing IT Networks Страницы: 54

Бренд: Velp Scientifica Страницы: 123

Бренд: IKA Страницы: 48

AP4600 MK3 Series

Бренд: Oxylitre Страницы: 15

Бренд: Bad Caf Страницы: 2

Бренд: STRIKEMASTER Страницы: 12

Бренд: TC Electronic Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды