Siemens Flender KMP Series Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 84

background image

BA 9142 en 02/2015

10.2

Clean the gear unit

NOTICE

Property damage

Damage to the gear unit from overheating is possible.
Dust deposits can affect the heat discharge through the housing surface and lead to overheating.
To prevent the build-up of dust on the gear unit, cleaning must be adjusted to the local operating
conditions.

•

Remove any dirt adhering to the gear unit, using a hard brush.

•

Remove any corrosion.

NOTICE

Property damage

Damage to the gear unit due to penetration of moisture is possible.
The gear unit must not be cleaned with high-pressure cleaning equipment.

10.3

Clean the air filter

Note

A period of 3 months applies to the cleaning of the air filter.
If a layer of dust has built up, the air filter must already be cleaned even before the 3-month period has
expired.

Note

If the air filter is protected with a filter cap, it must be disassembled before cleaning the air filter. After
cleaning the air filter, the filter cap must be reassembled.

•

Unscrew the air filter including the reducing screw.

•

Clean the air filter using a suitable cleaning agent.

•

Dry the air filter and/or blow with compressed air.

WARNING

Risk of injury to the eyes from pressurised air

Residual water and/or dirt particles can injure the eyes.
Wear suitable protective glasses.

NOTICE

Property damage

Damage to the gear unit due to penetration of foreign bodies is possible.
The penetration of foreign bodies into the gear unit must be prevented.

10.3.1

Replacing the air filter cartridge

Note

Annually

or when the air filter is heavily soiled.

•

Remove the air filter cover and replace the filter element (cleaning of the paper filter is not possible).

«
...
69
70
71
72
73
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: Palazzetti Страницы: 112

Бренд: Össur Страницы: 50

Бренд: Össur Страницы: 13

PRO-FLEX XC PXC0xyyz

Бренд: Össur Страницы: 68

Бренд: Össur Страницы: 25

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 18

i-Digits Quantum

Бренд: Össur Страницы: 337

FORMFIT TRACKER

Бренд: Össur Страницы: 7

Бренд: Össur Страницы: 97

FOOT-UP 07810 Series

Бренд: Össur Страницы: 19

FLEX-FOOT BALANCE Series

Бренд: Össur Страницы: 49

Exoform Carpal Tunnel Wrist

Бренд: Össur Страницы: 19

DIRECT SOCKET TOOL KIT

Бренд: Össur Страницы: 52

Avisa Line XL04

Бренд: FHF Страницы: 2

Бренд: Joerns Healthcare Страницы: 106

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды