Siemens Flender KMP Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 84

background image

BA 9142 en 02/2015

3.2

Special dangers and personal protective equipment

Depending on operating conditions, the surface of the gear unit may develop extreme temperatures.

WARNING

Risk of burns

Serious injury caused by burns on hot surfaces (> 55 °C) is possible.
Wear suitable protection gloves and protection clothing.

WARNING

Risk of low temperatures

Serious injury from cold damage (pain, numbness, frostbites) on cold surfaces (< 0 °C) is possible.
Wear suitable protection gloves and protection clothing.

WARNING

Risk of scalding

Serious injury from discharging hot operating media is possible when these are changed.
Wear suitable protection gloves, protection glasses and protection clothing.

WARNING

Risk of eye injury

Small foreign matter such as sand or dust can get into the cover plates of the rotating parts and might
be thrown back by these.
Wear suitable protective glasses.

Note

In addition to any generally prescribed personal protection equipment (protection shoes, protection
clothing, helmet, etc.) handling the gear unit requires wearing

suitable safety gloves

and

suitable

safety glasses

.

DANGER

Explosion hazard

Danger to life from ignition of a present explosive atmosphere is possible in the operation of the gear
unit.
The gear unit does

not comply

with the requirements of Directive 94/9/EC and therefore, in the area

of applicability of this directive, it

must

not

be used in areas with explosion hazard.

Should the gear unit be used outside the area of applicability of Directive 94/9/EC in areas with
explosion hazard, the nationally applying protective prescriptions with regard to explosion protection
must always be observed.

«
...
10
11
12
13
14
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды