Siemens Flender KMP Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 84

background image

BA 9142 en 02/2015

5.7

Oil temperature monitoring

The gear unit can be equipped with a resistance thermometer or temperature monitor for measuring the
oil temperature in the oil sump.
In order to measure the temperatures and/or temperature differences, the temperature monitor should be
connected to an evaluating device by the customer.

Note

In order to measure the temperatures and/or the temperature differences with a Pt 100 resistance
thermometer without evaluating instrument, the Pt 100 resistance thermometer must be connected to
an evaluation instrument provided by the customer.

A detailed illustration of the gear unit and the position of the add-on parts can found in the drawings of the
gear unit documentation.

Note

For operation and maintenance, the operating manuals in the order specific annex must be observed.
For technical data and control information, refer to the list of equipment prepared specifically for the
order.

«
...
33
34
35
36
37
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: Rangevision Страницы: 31

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: Hardt Страницы: 2

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренд: Sabre Страницы: 2

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: A.HABERKORN Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды