Siemens FCT010/DSL Скачать руководство пользователя страница 96

Страница: 96 / 180

10.2

Fault codes and corrective actions

10.2.1

Diagnostics

Icons

Message

Cause/Action

Sensor supply volt. out of
range

Contact your local Siemens representative.

Sensor supply volt. out of
range

Contact your local Siemens representative.

Temperature measure‐
ment fault

Turn off the power, wait 5 seconds and turn on the power
again. If the problem persists, contact your local Siemens
representative.

Temperature measure‐
ment fault

Turn off the power, wait 5 seconds and turn on the power
again. If the problem persists, contact your local Siemens
representative.

Temperature measure‐
ment fault

Turn off the power, wait 5 seconds and turn on the power
again. If the problem persists, contact your local Siemens
representative.

Temperature measure‐
ment fault

Turn off the power, wait 5 seconds and turn on the power
again. If the problem persists, contact your local Siemens
representative.

Flow values not valid

Can be due to problems with measured fluid or hardware
malfunction. If the problem persists, contact your local Sie‐
mens representative.

Flow values not valid

Can be due to problems with measured fluid or hardware
malfunction. If the problem persists, contact your local Sie‐
mens representative.

Flow values not valid

Can be due to problems with measured fluid or hardware
malfunction. If the problem persists, contact your local Sie‐
mens representative.

Flow values not valid

Can be due to problems with measured fluid or hardware
malfunction. If the problem persists, contact your local Sie‐
mens representative.

Invalid calibration data

Contact your local Siemens representative for recalibration.

Invalid compensation data Contact your local Siemens representative.

Malfunction in Pickup Am‐
plitude

Contact your local Siemens representative.

Malfunction in Pickup Am‐
plitude

Contact your local Siemens representative.

Malfunction in sensor driv‐
er

Contact your local Siemens representative.

Malfunction in sensor driv‐
er

Contact your local Siemens representative.

Diagnostics and troubleshooting FCT010
10.2 Fault codes and corrective actions

SITRANS MASS 2100 & FC300 (FCT010/DSL)

Operating Instructions, 06/2020, A5E39788682-AB

Содержание FCT010/DSL





















































































































































































Результаты поиска

Содержание FCT010/DSL

Отзывы:

Siemens FCT010/DSL, Руководство по эксплуатации, Страница: 96 / 180

Результаты поиска

Содержание FCT010/DSL

Отзывы: