Siemens FCT010/DSL Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 180

Siemens FCT010/DSL Скачать руководство пользователя страница 14

2.2.1

FCC Conformity

US Installations only: Federal Communications Commission (FCC) rules

Note
• This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.

• This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the operating instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference to radio communications, in which case the user will be required to
correct the interference at his own expense.

2.2.2

Conformity with European directives

The CE marking on the device symbolizes the conformity with the following European directives:

Electromagnetic
compatibility EMC
2014/30/EU

Directive of the European Parliament and of the Council on the harmoni‐
sation of the laws of the Member States relating to electromagnetic com‐
patibility

Low voltage direc‐
tive LVD
2014/35/EU

Directive of the European Parliament and of the Council on the harmoni‐
sation of the laws of the Member States relating to the making available
on the market of electrical equipment designed for use within certain
voltage limits

Atmosphère explo‐
sible ATEX
2014/34/EU

Directive of the European Parliament and the Council on the harmonisa‐
tion of the laws of the Member States relating to equipment and protec‐
tive systems intended for use in potentially explosive atmospheres

2011/65/EU RoHS

Directive of the European Parliament and the Council on the restriction of
the use of certain hazardous substances in electrical and electronic equip‐
ment

The applicable directives can be found in the EC conformity declaration of the specific device.

Note
CE declaration

The CE declaration certificate is available on the SensorFlash SD card delivered with the device.

Safety notes
2.2 Laws and directives

SITRANS MASS 2100 & FC300 (FCT010/DSL)

14

Operating Instructions, 06/2020, A5E39788682-AB

«
...
12
13
14
15
16
...
»

Содержание FCT010/DSL





















































































































































































Отзывы:

Нет отзывов