Siemens FC121-ZA Скачать руководство пользователя страница 24

Страница: 24 / 90

24
Smart Infrastructure

A6V10393190_h_en_--

2019-09-01

4.3.3

GB continuity

The GB continuity line allows a mixture of MCPs and detectors within the same zone.

In addition this mode supports a reliable operation, even though one or more detectors

are removed from its base. The CIE detect the removed detector and report a zone fault.

Technical:

Special detector bases equipped with a diode (1N5819):

DB110D part number S54372-F6-A1 or DB110RD part number S54372-F8-A1

MCPs require a Z-diode for direct alarming (AVC).

Siemens detectors 110-series or detectors with an alarm resistor are required for

delayed alarming (AVC, V1 / V2).

Each line must be terminated with EOL element Capacitor 10 µF.

Limitation: Max. 18 detectors per line is allowed due to voltage drop on the detector

base.

MCPs have no limitation and can be installed to reach the maximum of 32 devices.

Programming:

Configure

Zone

Zone 1 – n

Mode

GB continuity

Configure

Zone

Zone 1 – n

AVC

Via AVC timer MCP direct

NOTICE

See details of the specification in chapter 3.3.1.

Zone mode ‘GB continuity’ does NOT comply with EN 54-13.

Behavior of MCP in zone coincidence with function 'direct alarming' is not supported.

ZONE1

–

EOL

Содержание FC121-ZA



























































































Результаты поиска

Содержание FC121-ZA

Отзывы:

Похожие инструкции для FC121-ZA

Бренды по названию

Популярные бренды

Siemens FC121-ZA, Техническое руководство

Результаты поиска

Содержание FC121-ZA

Отзывы:

Похожие инструкции для FC121-ZA

Бренды по названию

Популярные бренды