Siemens 1LE5 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 142

background image

8.1.3

Safety instructions in operation - anti-condensation heating

Overheating as a result of the anti-condensation heating

If the anti-condensation heating is operated while the machine is operational, this can increase
the temperatures inside the machine and cause material damage.

• Install an interlock circuit that switches off the anti-condensation heating once the main

machine is switched on.

• Only switch on the anti-condensation heating after the motor has been switched off. Comply

with the data stamped on the plate of the anti-condensation heating, if available.

8.1.4

Safety instructions relating to ventilation

8.1.4.1

Safety instruction for forced ventilation (option)

Forced ventilation (optional): Type of cooling IC 416 in accordance with EN / IEC 60034-6

WARNING

Risk of burning

Operating the machine without external fan results in overheating. This may result in death,
personal injury and material damage.
• Never commission the machine without an external fan.

8.1.4.2

Safety instructions when operating machines with fan

CAUTION

Risk of injury when touching the fan

There is a risk of injury at machines equipped with a fan cover (e.g. on machines in the textile
industry), as the fan is not completely touch protected.
• Do not touch the rotating fan.
• Do not put your fingers into the larger air discharge openings.
• Prevent manual intervention by using suitable measures, e.g. appropriate housings or a

protective grating.

8.1.4.3

Machines with fan for the textile industry

In order to guarantee an essentially unobstructed flow of cooling air containing fluff, remains of
materials or similar dirt, machines used in the textile industry have a larger air discharge cross-
section between the edge of the cover and the cooling ribs of the machine frame.

Operation
8.1 Safety instructions for operation

1LE5, 1PC4 shaft heights 280 ... 355

90

Operating Instructions, 11/2022, A5E41454666A

«
...
90
91
92
93
94
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: YOODA Страницы: 6

Бренд: Flux Страницы: 28

Бренд: E-MAG Страницы: 30

Бренд: MSW Страницы: 159

RADIOMODULE 2G4

Бренд: Grundfos Страницы: 76

Бренд: Mitsubishi Electric Страницы: 102

Бренд: LCT Страницы: 25

Бренд: Volvo Penta Страницы: 96

Бренд: Lycoming Страницы: 120

Бренд: YS Страницы: 4

Бренд: Honda Страницы: 31

Бренд: CERTIFIED Страницы: 17

Бренд: Wood-mizer Страницы: 208

Бренд: Neodrives Страницы: 26

Бренд: YARDMAX Страницы: 28

Parilla LEOPARD

Бренд: IAME Страницы: 46

Бренд: Vanguard Страницы: 104

Бренд: King gates Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды