Siemens 1LE5 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 142

background image

Assembly

5

Comply with the following when carrying out any work on the machine:

• Comply with the general safety instructions (Page 19).

• Comply with the applicable national and sector-specific regulations.

• When using the motor within the European Union, comply with the specifications laid down

in EN 50110‑1 regarding safe operation of electrical equipment.

5.1

Safety instructions for installation

Injury and material damage caused by inappropriate fastening material

If screws of an incorrect property class have been selected or if they have been fastened to an
incorrect tightening torque, they may break or become loose. This will cause the machine to
move, which could damage the bearings. The rotor could smash into the machine enclosure and
machine parts could be flung out of place. This can result in death, serious injury or material
damage.

• Comply with the required property classes for screwed connections.

• Tighten the screwed connections to the specified tightening torques.

Injury and material damage caused by incorrect machine alignment

If the machine has not been properly aligned, this will mean the fastening parts are subjected
to stress/distortion. Screws may become loose or break, the machine will move, machine parts
could be flung out of place. This can result in death, serious injury or material damage.

• Carefully align the machine to the driven machine.

Material damage caused by improper handling

Mounting parts such as temperature sensors or speed sensors are attached to the machine and
could be ripped off or destroyed as a result of improper handling. This could lead to machine
malfunctions, extending even to total loss of the machine.

• Use suitable steps when carrying out installation work on the machine.

• Do not stand on cables or attachments during installation. Do not use attachments as steps.

Loss of conformity with European directives

In the delivery state, the machine corresponds to the requirements of the European directives.
Unauthorized changes or modifications to the machine lead to the loss of conformity with
European Directives and the loss of the associated warranty.

1LE5, 1PC4 shaft heights 280 ... 355
Operating Instructions, 11/2022, A5E41454666A

49

«
...
49
50
51
52
53
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: Daytona Страницы: 18

950-1020 MOTOR KIT 8504048 REV 2 1297

Бренд: TJERNLUND Страницы: 2

Бренд: YOODA Страницы: 7

Бренд: Kohler Страницы: 44

Бренд: O.S. engine Страницы: 13

MAX-15CV Series

Бренд: O.S. engine Страницы: 30

Бренд: O.S. engine Страницы: 18

Revenge CTM Series

Бренд: Absima Страницы: 3

Бренд: Yanmar Страницы: 224

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: NACIONAL MOTOR Страницы: 43

Бренд: Farymann Diesel Страницы: 110

Бренд: B&R Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды