Siemens 1LE5 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 142

background image

6.2.2

Terminal box

DANGER

Hazardous voltage

Electric motors have high voltages. When incorrectly handled, this can result in death or severe
injury.

Switch off the machine so that it is in a no-voltage condition before you open the terminal box.

NOTICE
Damage to the terminal box

If you incorrectly carry out work on or in the terminal box, this can result in material damage.
You must observe the following to avoid damaging the terminal box:
• Ensure that the components inside the terminal box are not damaged.
• It must be ensured that there are no foreign bodies, dirt or moisture in the terminal box.
• Close the terminal box using the original seal so that it is dust tight and water tight.
• Use O-rings or suitable flat gaskets to seal entries in the terminal box (DIN 42925) and other

open entries.

• Please observe the tightening torques for cable entries and other screws.
• Do not apply manual force to the terminal board. The terminal board mountings are

designed for the cable sizes specified in the documentation.

6.2.2.1

Circuit diagram inside the terminal box cover

Data on the connection and connecting the machine winding can be found in the circuit
diagram in the cover of the terminal box.

6.2.2.2

Direction of rotation

The standard motors are suitable for clockwise and counter-clockwise rotation.

For defined directions of rotation (direction of rotation arrow), appropriately connect the line
power cables.

• If you connect the line cables with phase sequence L1, L2, L3 at U, V, W or according to NEMA

at T1 T2 T3 , then the machine rotates in the clockwise direction.

• If you interchange 2 connections, e.g. L1, L2, L3 at V, U, W or according to NEMA at T2 T1 T3,

then the machine rotates counterclockwise.

Direction of ro‐

tation

According to IEC

According to NEMA

Line feeder cables

-

L1 L2 L3

L1 L2 L3

Electrical connection

6.2 Connecting the machine

1LE5, 1PC4 shaft heights 280 ... 355
Operating Instructions, 11/2022, A5E41454666A

67

«
...
67
68
69
70
71
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: Mack Страницы: 303

Бренд: BAFANG Страницы: 12

Бренд: Leroy-Somer Страницы: 8

Бренд: 3W Страницы: 19

Бренд: Nanni Страницы: 24

Бренд: Ofna Racing Страницы: 2

Бренд: Briggs & Stratton Страницы: 14

Smart Motor SM23166MT

Бренд: MOOG ANIMATICS Страницы: 32

EM-PMI540-T4000

Бренд: Danfoss Страницы: 71

Бренд: HOND Страницы: 48

iSV2-CAN Series

Бренд: Leadshine Страницы: 107

Бренд: Hino Motors Страницы: 339

Бренд: YS Страницы: 2

Бренд: Sisu Diesel Страницы: 80

Бренд: Greyhound Страницы: 19

Бренд: Nanomotion Страницы: 42

Бренд: O.S. engine Страницы: 9

Бренд: Honda Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды