Siemens 1LE5 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 142

background image

Archive the safety and commissioning notes provided in the scope of delivery as well as
the optionally available operating instructions so that these documents are always easily
accessible.

The rating plate optionally enclosed as a loose item with the delivery is provided to enable
the motor data to be attached on or near the machine or installation.

4.5

Transport and storage

4.5.1

Safety instructions for transport

Comply with the following when carrying out any work on the machine:

• Comply with the general safety instructions (Page 19).

• Comply with the applicable national and sector-specific regulations.

• When using the motor within the European Union, comply with the specifications laid down

in EN 50110‑1 regarding safe operation of electrical equipment.

The information required to correctly attach, lift and transport the machine - such as weight,
center of gravity and attachment points - is provided here:

• Machine dimension drawing and the associated explanations or the technical specifications

• Transport data

• Rating plate and lifting plate, if available

• Shipping parts list

• Packaging

Danger when incorrectly lifting and transporting

Danger of death, serious injury, or substantial material damage caused by tipping or falling
transported goods. Comply with the following safety instructions:

• All work must be performed with due caution and care.

• Comply with any notes in the shipping papers.

• Carefully comply with all of the handling information and markings on the packages

whenever transporting and putting the equipment into storage according to ISO 780.

• Only use suitable and correctly dimensioned lifting equipment, transport equipment and

industrial trucks.

Danger due to incorrect attachment and lifting

• Ensure that suitable lifting equipment is available.

• Only hoist the goods using the designated hoisting points and/or at marked positions. The

attachment points are not dimensioned for additional loads.

Preparing for use
4.5 Transport and storage

1LE5, 1PC4 shaft heights 280 ... 355

34

Operating Instructions, 11/2022, A5E41454666A

«
...
34
35
36
37
38
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: um Страницы: 115

Бренд: Westerbeke Страницы: 112

Бренд: Polini Страницы: 32

HO Union Pacific

Бренд: MTHTrains Страницы: 31

Бренд: IEF Werner Страницы: 38

7 HP 212 CC OHV

Бренд: Power Fist Страницы: 52

MerCruiser Diesel Inboard 2.8L

Бренд: Mercury Страницы: 93

ZA top SM210.60

Бренд: ZIEHL-ABEGG Страницы: 96

Бренд: GE Страницы: 10

Бренд: GE Страницы: 20

310000 - REVISION C

Бренд: GE Страницы: 24

Бренд: Grizzly Страницы: 2

Бренд: EX Model Engines Страницы: 2

Бренд: Nederman Страницы: 44

Бренд: CW Products Страницы: 4

Бренд: Lycoming Страницы: 74

Бренд: MULTIPLEX modell Страницы: 11

Бренд: Honda Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды