Siemens 1LE5 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 142

background image

Internal ground terminal

Comply with the following instructions when connecting up:

• Ensure that the connecting surface is bare and is protected against corrosion using a suitable

substance, e.g. acid-free Vaseline.

• Arrange the spring lock washer under the screw head.

• Locate the cable lug under the clamping bracket.

• Use the terminals designated for the grounding conductor in the terminal box.

• Observe the tightening torque (Page 134) for the locking screw.

External ground terminal

Comply with the following instructions when connecting up:

• Ensure that the connecting surface is bare and is protected against corrosion using a suitable

substance, e.g. acid-free Vaseline.

• Locate the cable lug between the contact bracket and the grounding bracket; do not remove

the contact bracket pressed into the enclosure.

• Arrange the flat washer and spring washer under the bolt head.

• Use the marked connection location for the grounding conductor on the stator housing.

• Observe the tightening torque (Page 134) for the locking screw.

6.5

Connecting the temperature sensor/anti-condensation heater

WARNING

Hazard due to electric shock

The installation of the temperature sensors for the winding monitoring with respect to the
winding is implemented according to the requirements for basic insulation. The temperature
sensor connections are located in terminal boxes, safe to touch, and have no protective
separation. This is the reason that in the case of a fault, a hazardous voltage can be present at
the measuring sensor cable. When touched, this can result in death, severe bodily injury and
material damage.
• When connecting the temperature sensor to external temperature monitoring devices,

when required, apply additional measures to fully comply with the requirements set out in
IEC 60664-1 or IEC 61800-5-1 "Hazard due to electric shock".

In addition to the current-dependent overload protective device located in the connecting
cables, use the optionally available integrated devices and equipment, for example,
temperature sensors, anti-condensation heating.

Electrical connection
6.5 Connecting the temperature sensor/anti-condensation heater

1LE5, 1PC4 shaft heights 280 ... 355

72

Operating Instructions, 11/2022, A5E41454666A

«
...
72
73
74
75
76
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: Ibiza Страницы: 3

Бренд: Aerotech Страницы: 59

Бренд: Avco Lycoming Страницы: 110

Бренд: Continental Motors Страницы: 146

Бренд: Ultima Страницы: 40

Sonesse Ultra 50 DC RS485

Бренд: SOMFY Страницы: 16

Бренд: Scania Страницы: 55

Бренд: Northern Lights Страницы: 42

Бренд: Leadshine Technology Страницы: 55

MotorLift RA20F

Бренд: Chamberlain Страницы: 24

Бренд: Chamberlain Страницы: 40

Бренд: Yanmar Страницы: 308

Бренд: Kingfisher Страницы: 10

Бренд: MULTIPLEX modell Страницы: 6

Бренд: Baumuller Страницы: 25

Бренд: LONCIN Страницы: 23

Бренд: Briggs & Stratton Страницы: 11

Бренд: Mitsubishi Heavy Industries Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды