Siemens 1LE5 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 142

background image

7.1.2

Converter operation

Converter operation
• If the motor design requires connection to a specific converter type, carefully check the

supplementary data on the rating plate/supplementary plate.

• Ensure that the converter is correctly parameterized. Depending on the design, you will find

some parameterization data on the rating plate of the machine. Further information is
provided in the converter documentation. If necessary, contact the Service Center.

• Check that the supplementary equipment and devices to monitor the machine are correctly

connected and are functioning correctly.

• In continuous operation, carefully ensure that the motor cannot exceed the specified upper

speed limit n

max

or fall below the lower speed limit n

min

.

The permissible acceleration time to the limit speed n

min

depends on the parameter

assignment.

7.1.3

Insulation resistance and polarization index

Measuring the insulation resistance and polarization index (PI) provides information on the
condition of the machine. It is therefore important to check the insulation resistance and the
polarization index at the following times:

• Before starting up a machine for the first time

• After an extended period in storage or downtime

• Within the scope of maintenance work

The following information is provided regarding the state of the winding insulation:

• Is the winding head insulation conductively contaminated?

• Has the winding insulation absorbed moisture?

From this, you can determine whether the machine needs commissioning or any necessary
measures such as cleaning and/or drying the winding:

• Can the machine be put into operation?

• Must the windings be cleaned or dried?

Detailed information on testing and the limit values can be found here:

"Testing the insulation resistance and polarization index" (Page 52)

7.1.4

Checking the machine cooling

Cooling
• Carefully check that it is guaranteed that the machine is cooled when it is being

commissioned.

Commissioning

7.1 Measures before commissioning

1LE5, 1PC4 shaft heights 280 ... 355
Operating Instructions, 11/2022, A5E41454666A

81

«
...
81
82
83
84
85
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: Rato Страницы: 65

Бренд: NOVAK Страницы: 2

Бренд: Briggs & Stratton Страницы: 12

Бренд: Wisconsin Motors Страницы: 46

Бренд: ACME motori Страницы: 23

Бренд: Toyota Страницы: 525

Бренд: RHINO Страницы: 9

Бренд: TAARKS Страницы: 9

ZAtop SM180.24/B

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: Daewoo Страницы: 126

RooloTube S Sun DuoFern Medium Series

Бренд: RADEMACHER Страницы: 72

Бренд: Nanni Страницы: 98

Бренд: BAFANG Страницы: 4

Бренд: Kärcher Страницы: 224

Бренд: Parker Страницы: 24

Бренд: Orientalmotor Страницы: 8

Бренд: GE Страницы: 41

Бренд: WÄRTSILÄ Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды