Sharp PC-AL Series Скачать руководство пользователя страница 37

Страница: 37 / 159

1-13

Gently push the tray back into the computer.

•

Do not press the eject button when the optical drive indicator is lit. It

may cause malfunction of the computer.

•

Do not leave the tray pulled out. Also, avoid touching the lens in the

tray. If the lens becomes dirty, the disc may malfunction.

Removing Disc

Make sure the optical drive indicator is not lit and press the eject button. The
optical drive tray will pop out.

Make sure the optical drive indicator is not lit before pressing the eject
button.

Gently pull out the tray.

Holding its edge, remove the disc from the tray.

Gently push the tray back into the computer.

Содержание PC-AL Series
































































































































































Результаты поиска

Содержание PC-AL Series

Отзывы:

Похожие инструкции для PC-AL Series

Бренды по названию

Популярные бренды

Sharp PC-AL Series, Руководство по эксплуатации

Результаты поиска

Содержание PC-AL Series

Отзывы:

Похожие инструкции для PC-AL Series

Бренды по названию

Популярные бренды