Sharp MX-M265N Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 311

background image

MX-M316N OPERATIONAL DESCRIPTIONS 11 – 3

B. Operational descriptions

(1)

Document size detection

Size detection on the document tray

The document width is detected with the RSPF document width sen-
sor (SPWS), and the document length is detected with the RSPF doc-
ument length sensors (SPLS1, SPLS2). The document size is judged
from the document width and the document length according to the
table below.

RSPF unit

(2)

Document scanning

The document scanning mode is available in 400dpi and 600dpi.

(3)

RSPF paper feed and transport operations

a. Paper feed operation

The transport motor is turned ON and the power of the transport
motor is transmitted to the pickup roller by turning ON the paper feed
clutch.

The pickup roller descends to pickup the top document and feed it to
the paper feed roller.

The paper feed roller feeds a document to the transport section.

At that time, the document is separated by the separation roller to pre-
vent double-feeding.

b. Single face scanning

The lead edge of the fed document is aligned (registration) by the reg-
istration roller, and passed through transport roller 1 to the document
scanning section, where images are scanned.

Then the document is passed through transport roller 2 to the paper
exit roller.

The rollers (the registration roller, transport rollers 1 and 2, the paper
exit roller) in the transport section are driven by the transport motor.

The paper exit roller (drive pulley) is pressed by the paper exit roller
pressure control solenoid.

When the read edge of the document passes the scanning section, the
both rollers are brought into close contact to supply the power for
paper exit.

1)

Document set (Document empty sensor ON)

2)

Paper feed start (1st sheet)

The pick-up roller descends. (The transport motor is booted. And
the paper feed clutch is ON.)

3)

Registration operation (1st sheet)

(Registration clutch ON)

(When a certain time passes after turning ON the registration
clutch, the paper feed clutch is turned OFF.)

4)

Scanning start (1st sheet)

Document size

Document length sensor

SPLS1

SPLS2

AB series

A5

OFF

OFF

B5

OFF

OFF

11" x 8.5"

OFF

OFF

A4

OFF

OFF

B5R

ON

OFF

A4R

ON

OFF

8.5" x 13"

ON

ON

B4

ON

ON

A3

ON

ON

11" x 17"

ON

ON

8.5" x 14"

ON

ON

8.5" x 13.4"

ON

ON

8.5" x 13.5"

ON

ON

Inch series

8.5" x 5.5"

OFF

OFF

11" x 8.5"

OFF

OFF

A4

OFF

OFF

11" x 8.5"R

ON

OFF

8.5" x 13"

ON

ON

8.5" x 14"

ON

ON

A3

ON

ON

11" x 17"

ON

ON

8.5" x 13.4"

ON

ON

Resolution

Document transport speed

400dpi

186mm/sec

600dpi

124mm/sec

30,3

30,3

3073

«
...
247
248
249
250
251
...
»

Содержание MX-M265N
























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-M265N

imagePROGRAF W8400

Бренд: Canon Страницы: 24

imagePROGRAF TZ-30000

Бренд: Canon Страницы: 66

imagePROGRAF W7200

Бренд: Canon Страницы: 126

imagePROGRAFi iPF840 series

Бренд: Canon Страницы: 149

Бренд: Canon Страницы: 166

iP4000 - PIXMA Photo Printer

Бренд: Canon Страницы: 2

Бренд: Olympus Страницы: 3

BW Remote Operators Software Kit-A1

Бренд: Canon Страницы: 20

imageRUNNER 2420

Бренд: Canon Страницы: 30

Бренд: Canon Страницы: 51

imageCLASS LBP325dn

Бренд: Canon Страницы: 252

Бренд: CAB Страницы: 40

Бренд: JCM Страницы: 70

WorkCentre Pro 40

Бренд: Xerox Страницы: 14

Бренд: Magicard Страницы: 2

Бренд: Magicard Страницы: 2

Бренд: Compuprint Страницы: 38

Бренд: Konica Minolta Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды