Sharp MX-M265N Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 311

Sharp MX-M265N Скачать руководство пользователя страница 19

MX-M316N SPECIFICATIONS 2 – 11

(11) Transmission Method

(12) Record Size

(13) F code communication

(14) Registration-related settings

*1: Since scan/Internet Fax/Fax uses the common address book,

the number of addresses allowed for registration is the sum
total of all modes.

*2: Quick key is the function to select an address based on the

registered number of each address within the book for address
selection. Users should be able to select a quick key number.

(15) Telephone functions

(16) Sound settings

(17) Others

6. Power consumption

The full configuration can be operated with the rated power source.

*1: At power-on timing

(with condition of dehumidify heater turned OFF)

Mode

FAX

Transmission time

2 seconds level (super G3/JBIG),
6 seconds level (G3 ECM)

Modem speed

Automatic fall-back : 33.6kbps 2.4kbps

Intercommunication

Super G3/G3

Communication line

General membership telephone line
(PSTN), independent business line
(PBX), F net.
(R-key for PBX setting: Germany/France)

ECM

Yes

Mode

FAX

Maximum record width

293mm

Record size

A3 ? A5/11" x 17" ? 5.5" x 8.5"

Mode

FAX

Sub-address

Yes (20 digits)

Password

Yes (20 digits)

Mode

FAX

One-touch/group

*1

E-mail
FTP
Desktop
SMB
FAX

1000 destinations
Use of LDAP allowed
Up to 500 registered addresses for
each group dial.
Registered name in 18 full-size
character (36 half-size characters)
One-touch dial receiver number
registration: within 64 digits for
receiver sub-a
passcode (including "/").

Program

Registration of addresses (groups),
settings (density, image quality) and
special functions in one set is
allowed. (48 of them)

Number of memory boxes

Registration of bulletin board/
confidential/relay broadcast is
allowed up to 100.
Registration name: 18 characters

Number of sender registration

1 (default) with 20 characters

Number of sender selection
registration

Total: 18 registrations (20
characters) (Sender selection: In
addition to default, 18 registrations
allowed)

Registration of polling approval
number

10 numbers/20 digits

Registration of Fax system
number (Sharp mode)

No

Registration of Fax polling
approval ID number (Sharp mode)

No

Fax relay ID registration (Sharp
mode)

No

Quick key (short cut registration)

*2

Yes (001 ? 1000)

Import/export of address book

Yes (By storage backup)

Black list (for France)

No

Mode

FAX

On-hook function

Yes

Hold

No

Setting of pause time

Yes (1 ? 15 seconds)

Telephone transmission during
power outage

No (External telephone transmission
allowed)

Tone pulse switching

Tone, Pulse, Auto (North America/
Taiwan)
* For the other destinations, set with

the soft switch.

Mode

Item

FAX

On-hook sound

Sound volume setting

1 - 9

Sound volume for calling

Sound volume setting

1 - 9, No

Line monitor sound

Sound volume setting

1 - 9, No

Reception sound

Sound volume setting

1 - 9, No

Transmission success sound

Sound volume setting

1 - 9, No

Transmission and reception
error sound

Sound volume setting

1 - 9, No

Sound setting for end of
original reading (image send)

Sound volume setting

Large/middle/
small/no sound

Mode

FAX

PC-FAX

Yes

FAST

Yes (SEC only)

Network FAST

No

Distinctive ring detection

Setting for each destination

100 V type

200 V type

Maximum rated power
Consumption

*1

1.44 kW

1.45kW

TEC value

26cpm machine

1.8 kWh

1.8 kWh

31cpm machine

2.1 kWh

2.1 kWh

35cpm machine

2.2 kWh

2.2 kWh

Fax waiting power consumption is 1W
*Condition of Standing by Network:
Connect with TCP/IP protocol only

Yes

No

Time to move into Preheat mode

1 minutes (default)

Recovery time from Preheat mode

10 seconds

Time to move into sleep mode

1 minute
(Default)

11 minutes
(Europe)
1 minute
(Other)

* After the remote job is done: 1

second (Default)

Recovery time from Sleep mode

20 seconds

1

: ‘15/Aug.

1

«
...
17
18
19
20
21
...
»

Содержание MX-M265N
























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды