manualshive.com logo in svg

Sharp MX-M265N, Руководство по обслуживанию

Поделиться
Скачать
Sharp MX-M265N Скачать руководство пользователя страница 165

MX-M316N  TROUBLESHOOTING  7 – 7

G. Details of error codes and countermeasures

 

A0-01

PCU PWB ROM error

 

A0-02

SCU PWB ROM error

 

A0-11

Firmware version inconsistency 
(MFP - PCU)

 

A0-15

Incompatible DSK BOOT and pro-
gram firmware

 

A0-20

Conflict firmware and EEPROM data
version (MFP)

 

A0-21

Conflict firmware and EEPROM data
version (PCU)

 

A0-22

Conflict firmware and EEPROM data
version (SCU)

 

E7-01

MFP image data error

 

E7-03

HDD trouble

 

E7-04

HDD-ASIC error

 

E7-07

SD card error

Trouble content

Detail

MFP

Cause

The firmware version-up is not completed properly by 
interruption of the power during the version-up 
operation, etc.
PCU PWB trouble.

Check & Remedy

Use SIM49-1 to perform the firmware version-up 
procedure again.
Replace the PCU PWB.

Trouble content

Detail

MFP

Cause

The firmware version-up is not completed properly by 
interruption of the power during the version-up 
operation, etc.
SCU PWB trouble.

Check & Remedy

Use SIM49-1 to perform the firmware version-up 
procedure again.
Replace the SCU PWB.

Trouble content

Detail

MFP

Cause

Firmware combination error between the MFP and 
the PCU.

Check & Remedy

Install the firmware in the all-firmware version-up 
mode.

Trouble content

Detail

MFP

Cause

Installation of the normal firmware was performed 
with a security kit enable.

Check & Remedy

Stop installation of the normal firmware.

Trouble content

Detail

MFP

Cause

Inconsistency between the MFP firmware version and 
the EEPROM data version.

Check & Remedy

Check the combination of the firmware.

Trouble content

Detail

PCU

Cause

Inconsistency between the PCU firmware version and 
the EEPROM data version.

Check & Remedy

Check the combination of the firmware.

Trouble content

Detail

SCU

Cause

Inconsistency between the SCU firmware version and 
the EEPROM data version.

Check & Remedy

Check the combination of the firmware.

Trouble content

Detail

MFP

Cause

Image data transfer error in the MFPC PWB.
MFPC PWB trouble.

Check & Remedy

Check connection of the connector and the harness 
of the MFPC PWB.
Check or replace the MFPC PWB.

Trouble content

Detail

MFP

Cause

Connector, harness connection trouble in the MFPC 
PWB and HDD.
HDD (error file management area) data abnormality 
(FAT breakage).
MFPC PWB trouble.

Check & Remedy

Check connection of the connector and the harness 
of the MFPC PWB and HDD.
Use SIM62-2, 3 to check read/write operations of the 
HDD.
Replace the HDD.
Check or replace the MFPC PWB.

Trouble content

Detail

MFP

Cause

HDD-ASIC trouble. (MFPC PWB trouble.)
An error occurs in the HDD-ASIC self test when 
booting.

Check & Remedy

Check or replace the MFPC PWB.

Trouble content

Detail

MFP

Cause

SD card trouble or contact error
MFPC PWB trouble.

Check & Remedy

Replace the SD card.
Check the SD card socket.
Replace the MFPC PWB.

Содержание MX-M265N
























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды