Sharp MX-M265N Скачать руководство пользователя страница 296 | Manualshive

Страница: 296 / 311

background image

MX-M316N OTHERS 13 – 4

2. Necessary steps when replacing the PWB, HDD and the SD Card

A. MFP substrate replacement procedure (work flow)

CAUTION: Registered user information will not be recovered if the MFP PWB is affected by U2-05 trouble. (*1)

1)

Attach the flash ROM, the memory, the EEPROM, the SD card etc. of the MFP PWB on the service parts MFP PWB and install it to the main unit.

CAUTION: Ground your body with grounding band during the work.

2)

When U2 trouble occurs, use SIM16 to cancel it.

3)

Set as follows after restarting the main unit.

At this timing, F6-21 may occur. Whether it may occur or not, go to execute procedure 1.

(1) Set the appropriate country code by Sim66-02 (clear the software switches related to FAX).

CAUTION: Make sure to execute even if the fax option is not installed on the machine.

B. Procedures necessary for HDD replacement

Note for HDD replacement

• Data of the following list are saved in the HDD of the complex machine. If the HDD operates normally and data backup is possible before replace-

ment, perform data backup and then replace the HDD.

• If the HDD does not operate normally, data cannot be backed up.

• The HDD replacement procedures with a broken HDD differs from that with a normal HDD.

Contents of this chapter

• HDD storage data and backup

• Replacement procedures when HDD storage data can be backed up

• Replacement procedures when HDD storage data cannot be backed up due to breakdown of HDD

• Reinstall and update procedures of Operation Manual data saved in HDD

• Reinstall and update procedures of watermark data.

(1)

HDD storage data and backup

Some HDD storage data can be backed up, and some other data cannot. Some HDD storage data can be reinstalled, and some other storage data
cannot.

If the HDD operates normally before replacement and data can be backed up, back up the data before replacement of the HDD referring to the HDD
storage data list. Then reinstall the data after replacement of the HDD.

a. HDD storage data list

*1: The e-Manual cannot be backed up, but can be reinstalled by using Sim49-3 and USB memory.

*2: Watermark data cannot be backed up, but can be reinstalled by using Sim49-5 and USB memory.

No.

Data kind

Before installation

(When shipping

from the factory)

After installation

(After use by

users)

Enable/

Disable of

data backup

Backup means

Enable/

Disable of

data reinstall

Data reinstall

procedures

Reinstall

operator

1

e-Manual

Available

Available

Disable

*1

Enable

Sim49-3

Service

2

Address book

Not available

Available

Enable

Sim56-2 /
Device cloning /
Storage backup

Enable

Sim56-2 /
Device cloning /
Storage backup

Service

3

Image send series
registration data (Sender’s
information, meta data, etc.)

Not available

Available

Enable

Sim56-2 /
Device cloning /
Storage backup

Enable

Sim56-2 /
Device cloning /
Storage backup

Service

4

User authentication
Account management

Not available

Available

Enable

Sim56-2

Enable

Sim56-2

Service

5

Japanese FEP dictionary
(Learning)

Not available

Available

Disable

Not available

Disable

—

6

Chinese FEP dictionary
(Learning)

Not available

Available

Disable

Not available

Disable

—

7

JOB LOG

Not available

Available

Enable

Perform with
WEB PAGE.

Disable

—

8

JOB completion list

Not available

Available

Disable

Not available

Disable

—

9

New N/A (FSS) information

Not available

Available

Disable

Not available

Disable

—

10

User font (Added)

Not available

Available

Disable

Not available

Enable

Perform with
WEB PAGE.

Service
or User

11

User macro

Not available

Available

Disable

Not available

Enable

Perform with
WEB PAGE.

12

Document filing

Not available

Available

Enable

Perform with
WEB PAGE.

Enable

Perform with
WEB PAGE.

13

Some of system setting
data

Not available

Available

Enable

Sim56-2 /
Device cloning /
Storage backup

Enable

Sim56-2 /
Device cloning /
Storage backup

Service

14

Watermark

Available

Available

Disable

*2

Enable

Sim49-5

Service

15

FAX reception data

Not available

Available

Enable

Sim66-62

Disable

—

—

«
...
294
295
296
297
298
...
»

Содержание MX-M265N
























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-M265N

Бренд: Canon Страницы: 58

image Prograf iPF680 Series

Бренд: Canon Страницы: 132

Бренд: Canon Страницы: 44

imageClass LBP6230dw

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 2

imageprograf IPF785

Бренд: Canon Страницы: 42

Бренд: Canon Страницы: 148

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 6

Color Bubble Jet BJC-1000 Series

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 105

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 68

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды