Sharp AR M162 - B/W Laser - All-in-One Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 372

Sharp AR M162 - B/W Laser - All-in-One Скачать руководство пользователя страница 36

34

TROUBLESHOOTING AND MAINTENANCE

MISFEED IN TRAY 2

1

Open the side cover.

Grasp the handle to open the
side cover.

2

Remove the misfed paper.

Be careful not to tear the misfed
paper during removal.

3

If there was no misfed paper in step 2,
pull out tray 2 and remove the misfed
paper.

Be careful not to tear the misfed
paper during removal.

4

Gently close the side cover.

The message "

Clear paper

path." will be cleared and
copying will be possible.

5

Gently push tray 2 into the machine.

Push the tray in completely.

• Make sure that there is no misfed paper in the tray before pulling it out. (Page 31)
• Also use the following procedure to remove misfeeds that occur in the 250-sheet paper feed unit and the 2 x

500-sheet paper feed unit.

Note

If the message does not clear, check again
to make sure that no pieces of paper
remain.

Side cover

Note

Side cover

2 x 250-sheet paper feed unit (AR-D25)

«
...
34
35
36
37
38
...
»

Содержание AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Отзывы:

Нет отзывов