Sentec SDM Скачать руководство пользователя страница 63

Страница: 63 / 93

4 Troubleshooting

SenTec Digital Monitoring System

Problem

Possible Cause(s)

Recommended action(s)

SenTec TC Sensor
defective

If the problem persists the SenTec TC Sensor
is defect. Replace it with a new one.

P0305

PCO2
sensitivity of
the sensor

low /
Message
‘Sensor
problem 12’

PO2
sensitivity of
the PO2
sensor low /

Message
‘Sensor
problem 72’

Membrane related

(defective or dried
up electrolyte)

Change the membrane:

if it is damaged or missing, has a loose fit,
or if there is trapped air or dry electrolyte
under the membrane

if the ‘Sensitivity Test’ fails.

Note: If the ‘Sensitivity Test’ fails the
message ‘Sensor problem 12’ displays and
PCO2 subsequently will be flagged as invalid

Note: If the ‘Sensitivity Test’ fails the
message ‘Sensor problem 72’ displays and
PO2 subsequently will be flagged as invalid

PCO2 electrode

and/ or white PO2
sensing spot
contaminated

If after having changed the sensor membrane

the ‘Sensitivity Test’ still fails contact qualified
service personnel to clean the sensor without
membrane.
Clean/Inspect the sensor as described in

section

3.1.7

“Cleaning / Inspecting without

Membrane” and perform the ‘Sensitivity Test’

as described in

section

3.1.8

“PCO2 / PO2

Sensitivity & Calibration Duration”.
If problem persists contact SenTec authorized
service personnel.

SenTec TC Sensor
defective

If the problem persists the SenTec TC Sensor
is defect. Replace it with a new one.

Docking Station
Solenoid Valve
defective

Note: Only for SMB

7.00 or lower.

If problem persists the Docking Station
Solenoid Valve is defective. Replace it by
original replacement parts according to the

Repair Manual for the SDMS.

To be performed by SenTec authorized

service technicians only.

P0306

Status
Message
‘Temp. limiter

active’ /
Message
‘Sensor

problem 38-
42’

Temperature of the

SenTec TC Sensor
is increased, e.g.
because of

warming lamps or
electric blankets

Shield sensor from heat.

SenTec TC Sensor
defective

If the problem persists the SenTec TC Sensor
is defect. Replace it with a new one.

SDM defective

Refer to

section

4.2.4

“SDM specific

troubleshooting” to further evaluate the

problem.

Содержание SDM






























































































Результаты поиска

Содержание SDM

Отзывы:

Бренды по названию

Популярные бренды

Sentec SDM, Руководство по обслуживанию

Результаты поиска

Содержание SDM

Отзывы:

Бренды по названию

Популярные бренды