manualshive.com logo in svg

Sentec SDM, Руководство по обслуживанию

Поделиться
Скачать
Sentec SDM Скачать руководство пользователя страница 62

4 Troubleshooting 

 

 

HB-005615-j 

56 

Problem 

Possible Cause(s) 

Recommended action(s) 

Clean the sensor as described in 

section 

3.1.7

 

“Cleaning / Inspecting without Membrane”. 

Then calibrate the sensor. 

SenTec TC Sensor 
defective 

If the problem persists the SenTec TC Sensor 
is defect. Replace it with a new one. 

Calibration Module 

defective 

Replace the Calibration Module according to 

the 

Repair Manual for the SDMS. 

 

 

To be performed by SenTec authorized 

service technicians only.

 

SDM defective 

Refer to 

section 

4.2.4

 “SDM specific 

troubleshooting ” to further evaluate the 

problem. 

P0304

 

PCO2 slow 
(too slow) / 
Message 

‘Sensor 
problem 11, 
14’ 
 

OR 
 
PO2 slow 

(too slow) / 
Message 
‘Sensor 

problem 74’ 

Membrane related 

(defective or dried 
up electrolyte) 

Change the membrane : 

-

 

if it is damaged or missing, has a loose fit, 

or if there is trapped air or dry electrolyte 
under the membrane  

-

 

sensor calibration takes almost 14 
minutes or cannot be completed within 14 
minutes 

Note: If the PCO2 calibration takes 14 

minutes the message ‘PCO2 slow’ displays 
and PCO2 subsequently will be flagged as 
questionable. 
Note: If the PCO2 calibration cannot be 

finished within 14 minutes the message 
‘Sensor problem 11’ displays and PCO2 
subsequently will be flagged as invalid. 
Note: If the calibration cannot be finished 
within approx. 30 minutes – due to failed 

extended calibration – the message ‘Sensor 
problem 14’ displays and PCO2 subsequently 
will be flagged as invalid. 
Note: If the PO2 calibration cannot be 

finished within 14 minutes the message 
‘Sensor problem 74’ displays and PO2 
subsequently will be flagged as invalid. 

PCO2 electrode 
and/ or white PO2 

sensing spot 
contaminated 

If after having changed the sensor membrane 
the calibration still takes almost 14 minutes or 

cannot be completed within 14 minutes 
contact qualified service personnel to clean 
the sensor without membrane. 
Clean the sensor as described in 

section 

3.1.7

 

“Cleaning / Inspecting without Membrane”. 

Then calibrate the sensor. 

Содержание SDM






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды