manualshive.com logo in svg

Sentec SDM, Руководство по обслуживанию

Поделиться
Скачать
Sentec SDM Скачать руководство пользователя страница 26

3 Maintenance/Safety & Functionality Tests 

 

 

HB-005615-j 

20 

3.1.9

 

PCO2 / PO2 Slope Test 

Tools: 

 

Sensor Tester Unit (alternatively an SDM can be used) 

 

V-STATS Software (optional, to enable calibration curve on SDM) 

 

interface online log software, e.g. “Hterm” freeware available in 
the  internet  (optional,  for  easier  on-line  logging  of  calibration 
values) 

 

Note:  For a V-Sign™ Sensor only the PCO2 Slope Test must be performed. For an 

OxiVenT™ Sensor both, PCO2 and PO2 Slope Test, must be performed. 

Note:  The  Slope  Test  can  also  be  performed  using  a  second  SDM  instead  of  a 

Sensor Tester Unit. Also, a single SDM can be used (requiring changing gas 
bottles after each step). If you use one single SDM, make sure that 
the correct gas bottle with the correct gas concentration (with 8% 
CO2, 12% O2) remains in the SDM at the end of the test. 

Note:  Prior performing the Slope Test please ensure that the sensor is properly 

stabilized, i.e. stored for at least 4 hours in the Docking Station with the 

monitor switched on. For an overview about the Slope Test please refer to 

Figure 6  

Examples: PCO2 and PO2 Slope Test. 

Note:  After  the  test  ensure  to  reset  all  parameters  and  settings  to  the  ones 

originally selected by your customer  

 
1.

 

You  may  optionally  activate  the  display  of  the  calibration  curve  by  using  “V-
STATS” (PC-Software for the SDM). 

2.

 

Verify proper function of the SenTec Sensor Tester (ST-DSU). In particular verify 
the integrity of the Docking Station. Verify the expiration date of the test gas 
bottles. 

3.

 

Power-cycle the SDM before starting the Slope Test (i.e. turn the SDM off and on 

again to ensure that the next calibration is a so-called `Initial Calibration´, which 
calibrates both, the PCO2 and PO2 channel). 

4.

 

Verify that the sensor SET temperature is 42°C or else set the sensor temperature 

to  42°C  (for  V-Sign™  Sensor  and  OxiVenT™  Sensor),  the  ‘Severinghaus 
Correction Mode’ is set to AUTO and that the local atmospheric pressure is at 
least  600  mmHg  (80  kPa)  (see  respective  icon).  Note  down  the  atmospheric 

pressure  value.  If  you  are  using  an  OxiVenT™  Sensor  ensure  that  the  PO2-
parameter is enabled (e.g. select Neo-mode and enable PCO2/PO2 parameters 
and set sensor SET-temperature to 42°C). 

5.

 

Insert the sensor into the Docking Station of the SDM. Sensor calibration starts 

automatically.  If  not:  Use  the  menu-function  ‘Measurement  Settings  /  PCO2 
Settings / Calibrate sensor’ to manually activate the sensor calibration (note: In 
case  of  an  OxiVenT™  Sensor  this  function  will  initiate  a  PCO2  and  PO2 

calibration). After the calibration (with 8% CO2, 12% O2) is finished please wait 
6 minutes (this is to ensure that no gas leak is present in the Docking Station of 
the SDM). 

Содержание SDM






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды