Sentec SDM Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 93

Sentec SDM Скачать руководство пользователя страница 79

5 Repairs of the SDM

SenTec Digital Monitoring System

73

5

Repairs of the SDM

Repairs described in this chapter do not require opening the SDM`s cover and shall be
carried out by qualified service personnel only.
Repairs that require opening the cover of the SDM are to be performed by SenTec
authorized service technicians only (i.e. trained by SenTec AG or accredited partners)
and are described in detail within the

Repair Manual.

Prior to maintenance, service or repairs all components of the SDMS must be cleaned
and disinfected. If equipment is send to service personnel, a local SenTec
representative or to SenTec AG a completed

“Certificate for Disinfection” (see section

) must be attached.

If you need to return devices for service or repair follow the shipment instructions in

section

“Instructions for Shipment”.

Send defective parts together with the completed

"Repair or Investigation Request

Form" to your local SenTec representative. The "Repair or Investigation Request Form"

may be copied from

section

“Repair or Investigation Request Form”.

To ensure traceability – a regulatory requirement – SenTec AG needs to know the

serial and LOT numbers as well as software versions of all components of the SDMS.
This means, if you replace parts of the SDM of if you perform a software
update you must report the serial number of the respective SDM and the
serial and LOT numbers of the replaced parts using the

“Repair Reporting

Form” see section

to your local distributor.

For spare parts and test tools refer to in

section

“Testing Accessories and Spare

Tools



Screwdriver large slotted 3 mm



A pair of pointed tweezers



A pair of normal tweezers

WARNING: Maintenance and repairs requiring removal of the
case or covers may only be carried out by SenTec authorized
service personnel trained by SenTec AG or accredited partners.

WARNING: Use only accessories and spare parts supplied or
recommended by SenTec AG. Do not perform other service and
repair activities than specified and described by SenTec AG.

Failure to comply may result in physical injury, inaccurate
measurements, and/or damage to the device.

«
...
77
78
79
80
81
...
»

Содержание SDM






























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды