Sentec SDM Скачать руководство пользователя страница 75

Страница: 75 / 93

4 Troubleshooting

SenTec Digital Monitoring System

4.2.5

Docking Station specific troubleshooting

Table 10

Docking Station specific troubleshooting

Problem

Possible Cause(s)

Recommended action(s)

P0500

Docking
Station door
does not

close
properly

Sensor cable
jammed in the door

Adjust cable and close the Docking Station
door properly.

Sensor not inserted
properly in the
Docking Station
door.

Insert the sensor properly and close the door.

Mechanical defect

of the Docking
Station door

Contact qualified service personnel.

Mechanical defect
of the Docking
Station door

Replace Docking Station door according to

section

5.5

“Replacement, Docking Station

Door”.

Gasket not placed

correctly

Place gasket correctly in the chamber in the

Docking Station according to

section

5.6

“Replacement, Docking Station Gasket”.

Docking Station
door mechanically

defective

Replace Support for Docking Station Door
according to the

Repair Manual for the SDMS.

To be performed by SenTec authorized

service technicians only

P0501

Message

‘Docking
Station Fault’
is displayed

Contaminations
(e.g. gel residues)
disturb the gas flow

Clean Docking Station and SenTec TC Sensor
and then insert the sensor into the Docking
Station.
If problem persists contact qualified service
personnel.
Note: Refer to the

Instruction Manual for the

SDMS.

Docking Station
defective

Contact SenTec authorized service personnel.

Docking Station

Module defective

Replace Docking Station Module according to

the

Repair Manual for the SDMS.

To be performed by SenTec authorized

service technicians only

P0502

Message ‘Gas

leak in DS’ is
displayed or
a gas leak is

Sensor not properly
positioned in

Docking Station
during last
calibration.

Verify that the sensor is clean and is properly
placed into the holder at the inside of the

Docking Station door and that the door
properly closes (refer to the

Instruction

Manual for the SDMS).

Содержание SDM






























































































Результаты поиска

Содержание SDM

Отзывы:

Бренды по названию

Популярные бренды

Sentec SDM, Руководство по обслуживанию

Результаты поиска

Содержание SDM

Отзывы:

Бренды по названию

Популярные бренды