manualshive.com logo in svg

Sentec SDM, Руководство по обслуживанию

Поделиться
Скачать
Sentec SDM Скачать руководство пользователя страница 27

 

3 Maintenance/Safety & Functionality Tests 

 

 

SenTec Digital Monitoring System 

 

 

 

21 

6.

 

Insert the test bottle with 5% CO2 and 6% O2 into the Sensor Tester. Use the 

menu-function  ‘PCO2  Settings  /  Calibrate  Sensor’  or  press  the  ENTER  Button 
twice to start a calibration. Record PCO2 (5%) and PO2 (6%), i.e. the PCO2/PO2 
values just before termination of the calibration. After the calibration is finished 

please wait 6 minutes (this is to ensure that no gas leak is present in the Docking 
Station of the SenTec Sensor Tester).  
Note: If you are using an SDM for the Slope Test and in case of an OxiVenT™ 

Sensor the message `Sensor Problem 73´ appears on the SDM at this stage. This 
is an expected behavior of the sensor. 

7.

 

Compare the measured PCO2 (5%) and PO2 (6%) with the values expected for 
the respective local atmospheric pressure (see Slope Test Control Table). PCO2 

(5%) should be within 5_min and 5_max. PO2 (6%) should be within 6_min and 
6_max. 

8.

 

Remove  the  sensor  from  the  Docking  Station  of  the  Sensor  Tester,  insert  the 

sensor into the Docking Station of the SDM and use the menu-‘PCO2 Settings / 
Calibrate Sensor’ to start a calibration (with 8% CO2, 12% O2).  
Note: In case of an OxiVenT™ Sensor the message `Sensor Problem 73´ will 
disappear from the SDM`s display at this stage. 

9.

 

Insert the test bottle with 30% CO2 and 21% O2 into the Sensor Tester. Use the 
menu-function  ‘PCO2  Settings  /  Calibrate  Sensor’  or  press  the  ENTER  Button 
twice to start a calibration.  Wait until calibration is finished and record PCO2 

(30%)  and  PO2  (21%),  i.e.  the  PCO2  value  just  before  termination  of  the 
calibration. 
Note: If you are using an SDM for the Slope Test and in case of an OxiVenT™ 

Sensor the message `Sensor Problem 73´ appears on the SDM at this stage. This 
is an expected behavior of the sensor. 

10.

 

Compare the measured PCO2 (30%) and PO2 (21%) with the values expected 
for  the  respective  local  atmospheric  pressure  (see  Slope  Test  Control  Table). 

PCO2 (30%) should be within 30_min and 30_max. PO2 (21%) should be within 
21_min and 21_max. 

11.

 

In case of an OxiVenT™ Sensor: In order to clear the message `Sensor Problem 

73´ you must do either of the following: a) power-cycle the SDM; b) connect the 
OxiVenT™  Sensor  to  a  different  SDM;  or  c)  perform  a  calibration  with  the 
standard gas concentration (i.e. with 8% CO2, 12% O2). 

12.

 

If you have used one single SDM for the Slope Test, always perform a calibration 
with the standard gas concentration (i.e. with 8% CO2, 12% O2) at the end of 
the Slope Test. 

If  the  readings  are  outside  the  respective  limits  replace  the  sensor  and 
report to SenTec the sensor behavior/replacement. 
 

Содержание SDM






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды