manualshive.com logo in svg

Sentec SDM, Руководство по обслуживанию

Поделиться
Скачать
Sentec SDM Скачать руководство пользователя страница 24

3 Maintenance/Safety & Functionality Tests 

 

 

HB-005615-j 

18 

In  case  of  loose  fit,  damage  or  trapped  air  you  must  repeat  the 

membrane change. Otherwise confirm the membrane change in the menu of 
the monitor and calibrate sensor. 

 

 

 

 

Figure 5 

Inspection after remembraning the sensor 

 
 

3.1.8

 

PCO2 / PO2 Sensitivity & Calibration Duration  

 

WARNING: A wrong barometer reading or a gas leak can lead 
to  a  false  positive/negative  test  result.  Prior  to  performing  a 

‘Sensitivity Test’ verify Docking Station integrity/cleanliness (

see 

section 

3.3

  “Docking  Station”)  and  barometer  function  (see 

section 

3.2.11

 “Barometric Pressure”). 

 

 

 

Note:  If the procedure below is not strictly followed the ‘Sensitivity Test’ will abort. 

Strictly observe the indicated times. ‘Sensor problem 12’ (PCO2 sensitivity) 
or  ‘Sensor  problem  72’  (PO2  sensitivity)  will  only  reset,  if  the  test  was 
successful. 

Note:  If a V-Sign™ Sensor is connected to the SDM the function ‘Sensitivity Test’ 

will test the sensor`s PCO2 sensitivity. If an OxiVenT™ Sensor is connected 
to the SDM the function ‘Sensitivity Test’ will test the sensor`s PCO2 and 
PO2 sensitivity in parallel. 

 
Test the PCO2/PO2 sensitivity as follows: 
 

1.

 

Verify that the sensor SET temperature is 42°C (in case of a V-Sign™ Sensor) or 
43°C (in case of an OxiVenT™ Sensor) and that the local atmospheric pressure 
is at least 600 mmHg (80 kPa) (see respective icon). 

Note:  You  may  optionally  activate  the  display  of  the  calibration  curve  by 

using “V-STATS™” (PC-Software for the SDM). 

2.

 

Insert the sensor into the Docking Station. 

3.

 

Use the menu-function ‘Measurement Settings / PCO2 Settings / Sensitivity Test’ 
OR the menu-function ‘Measurement Settings / PO2 Settings / Sensitivity Test’ to 
activate  the  test  (both  menu-functions  will  initiate  the  same  test).  The  Status 

Содержание SDM






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды